Puffwagon Puff Gold Donating Members 15,862 Member For: 9y 9m 19d Gender: Male Location: South Australia Posted 05/09/24 07:14 AM Author Share Posted 05/09/24 07:14 AM Oh yeah I ran gate pressure to start with...180awkw on 3.5psi lol Link to comment Share on other sites More sharing options...
hjtrbo Bronze Donating Members 320 Member For: 13y 9m 29d Posted 05/09/24 11:48 AM Share Posted 05/09/24 11:48 AM Hey, so that fuel issue is still there? Link to comment Share on other sites More sharing options...
Puffwagon Puff Gold Donating Members 15,862 Member For: 9y 9m 19d Gender: Male Location: South Australia Posted 05/09/24 12:13 PM Author Share Posted 05/09/24 12:13 PM (edited) Yes it's still there, along with the cutting out issue, despite changing the battery. I'm going to do the coils, valve guide seals, valve springs and retainers tomorrow and just for a sanity check, change the cam timing to a known good economy position. Should take about 4 or 5 hours if I smash it, lucky I've had a coles order today that included plenty of energy drinks!!! Edited 05/09/24 12:14 PM by Puffwagon Deez nuts Link to comment Share on other sites More sharing options...
Puffwagon Puff Gold Donating Members 15,862 Member For: 9y 9m 19d Gender: Male Location: South Australia Posted 06/09/24 06:31 AM Author Share Posted 06/09/24 06:31 AM New FG coils fitted today, it fixed the cutting out issue so that's good. It also was going brrr on the dyno yesterday over about 12psi so it fixed that too. Tried to crank some boost into it today and it hit 32psi at 3200rpm then hit the boost cut. Turned it down slightly but there's a godamn boost leak on the intake side somewhere, I can hear it and it isn't holding boost. It wasn't there before the rebuild so I've just gotta have a look at what I've touched and get it sorted. Also I remembered that I already replaced the valve stem seals so I ain't changing sh*t! Just another day in the life lol 1 Link to comment Share on other sites More sharing options...
k31th less WHY; more WOT Site Developer 28,952 Member For: 16y 7m 7d Gender: Male Location: Melbourne Posted 06/09/24 07:01 AM Share Posted 06/09/24 07:01 AM only 32psi taking it slow, I see Link to comment Share on other sites More sharing options...
Puffwagon Puff Gold Donating Members 15,862 Member For: 9y 9m 19d Gender: Male Location: South Australia Posted 06/09/24 07:06 AM Author Share Posted 06/09/24 07:06 AM I overestimated the amount of duty cycle needed to make boost and I had the cut set at 30 just in case. Haha I was aiming for 25psi which is pretty normal, I will send the farker when the time comes, you can bet your whiskers 1 Link to comment Share on other sites More sharing options...
Puffwagon Puff Gold Donating Members 15,862 Member For: 9y 9m 19d Gender: Male Location: South Australia Posted 09/09/24 09:25 AM Author Share Posted 09/09/24 09:25 AM Fitted an 85mm turbo yesterday/this morning. It appears to come on around 4000rpm so not terrible. Got a boost leak somewhere so gotta find that, it makes 10psi with 15psi gate spring so yerp. Also fitted my modified vct gears to the cams today, helps a bit with low end power. Link to comment Share on other sites More sharing options...
Puffwagon Puff Gold Donating Members 15,862 Member For: 9y 9m 19d Gender: Male Location: South Australia Posted 10/09/24 08:40 AM Author Share Posted 10/09/24 08:40 AM Fitted hectic valve springs and titanium retainers, along with new valve guide seals. Vct immediately got unhappy so locked it out again. 50th time the rocker cover has been off this week Gonna have to use a smoke tester to find the boost leak cos I CBF pulling sh*t apart anymore. The turbo is making positive pressure at 3350rpm, not bad 1 Link to comment Share on other sites More sharing options...
Puffwagon Puff Gold Donating Members 15,862 Member For: 9y 9m 19d Gender: Male Location: South Australia Posted 11/09/24 07:48 AM Author Share Posted 11/09/24 07:48 AM Boost leak turned out to be the throttle body, more than likely the water meth damaged the seal or whatever is in there. I'll pull it apart for a look, might be able to repair it. Anyway I put a new TB in there so it's sorted, and I bought another one just in case I need a spare. Still wasn't making boost though...Haltech did an update and limited the throttle to 50%. That was a fun one to solve. Now that it actually gets full throttle the turbo is in positive pressure before 2500rpm. I've only done one quick run at 26psi with no timing in it but it goes like feck with that big arse turbo. Don't get me wrong it has some lag to it, but I can live with that and it's good enough to chop at roll racing. Will get it back on the dyno one day to see what I can do with it, maybe Saturday. 2 Link to comment Share on other sites More sharing options...
Puffwagon Puff Gold Donating Members 15,862 Member For: 9y 9m 19d Gender: Male Location: South Australia Posted 12/09/24 06:40 AM Author Share Posted 12/09/24 06:40 AM Here's an interesting one...the car is using triple the fuel at idle, over double at cruise, triple or more while gentle accelerating and a normal amount at WOT. I've ordered a leak/smoke machine to check the hot side, so it will be interesting to see if there is a leak causing the high fuel usage. Lol it was hitting the 30psi cut on the shifts so I upped the cut to 35psi. Should be sorted in that area at least 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now