gaz097 Bronze Donating Members 1,752 Member For: 13y 5m 25d Posted 28/03/21 11:16 AM Share Posted 28/03/21 11:16 AM Are you going to do any thing to help it shift quicker? Wot box spark cut etc?Do malwoods offer a faceplate option? Link to comment Share on other sites More sharing options...
Tom Tucker Donating Members 673 Member For: 5y 6m 15d Posted 28/03/21 10:27 PM Author Share Posted 28/03/21 10:27 PM It comes with Mal Woods short shift assembly, and I have a Hurst shifter to go on that. I'll have to do some research on ignition cut. I'm assuming I need a pressure switch somewhere. Link to comment Share on other sites More sharing options...
gaz097 Bronze Donating Members 1,752 Member For: 13y 5m 25d Posted 29/03/21 01:11 AM Share Posted 29/03/21 01:11 AM Few different ways. Clutch switch with rpm input is common 1 Link to comment Share on other sites More sharing options...
Tom Tucker Donating Members 673 Member For: 5y 6m 15d Posted 05/05/21 08:36 AM Author Share Posted 05/05/21 08:36 AM So installed the big 1400hp axles. And replaced all the suspension bushes in the rear. Learnt a lot doing it myself. Dropped the car off today to get the engine built. Will take a few months, but the progress continues. Will finally be able to stretch the G35-900. 3 Link to comment Share on other sites More sharing options...
JETURBO ...JD TUNING ADELAIDE... Gold Donating Members 23,708 Member For: 16y 7m 15d Gender: Male Location: Adelaide Posted 05/05/21 08:46 AM Share Posted 05/05/21 08:46 AM Who’s doing the build mate ? Whats the specs on it ? Link to comment Share on other sites More sharing options...
Puffwagon Trust me bro... Gold Donating Members 16,056 Member For: 9y 11m 16d Gender: Male Location: South Australia Posted 05/05/21 08:47 AM Share Posted 05/05/21 08:47 AM 10 minutes ago, Tom Tucker said: Will finally be able to stretch replace the G35-900. FTFY 1 Link to comment Share on other sites More sharing options...
Tom Tucker Donating Members 673 Member For: 5y 6m 15d Posted 05/05/21 09:24 AM Author Share Posted 05/05/21 09:24 AM 13 minutes ago, JETURBO said: Who’s doing the build mate ? Whats the specs on it ? Using the builder that East Coast Customs uses, Tremaniac. They've done all the tuning, so I'm keeping it in house to make sure any potential issues are sorted. It'll just be a basic build. CP Bullet pistons, not sure what rods yet. Tremaniac like using carillo. Upgraded timing gear, the usual stuff. Keeping 12mm head studs with washers. Not sure about cams. I really want a different sound and higher power band, but no spool penalty. Will probably keep stock unless they're pitted. Any suggestions? Got the T-56 Magnum to throw in as well. Interestingly, East Coast Customs do big LS builds and one of the guys was telling me some of their customers with big blowers have broken TR6060 boxes, and replaced with magnums, none of which have ever broken. I thought they were the same internally... Link to comment Share on other sites More sharing options...
Puffwagon Trust me bro... Gold Donating Members 16,056 Member For: 9y 11m 16d Gender: Male Location: South Australia Posted 05/05/21 09:32 AM Share Posted 05/05/21 09:32 AM (edited) Here is a review of some Dynomite Performance cams that show it making power for longer in the rev range with no spool penalty. Edited 05/05/21 09:36 AM by Puffwagon Why not? 1 1 Link to comment Share on other sites More sharing options...
adams355 Member 529 Member For: 7y 8m 14d Gender: Male Location: Brisbane Posted 05/05/21 11:24 AM Share Posted 05/05/21 11:24 AM Me likey cams, I think TBRE have a couple as well, not sure if they are off the shelf though, earlier boost and longer rpm. I think these engines were supposed to rev to (make power to) 6k but ford realised oh sh*t these are going to be a bit wild and smash their v8's. 1 Link to comment Share on other sites More sharing options...
sixman Donating Members 600 Member For: 20y 5m 24d Gender: Male Location: Hills District, NSW Posted 08/05/21 12:19 AM Share Posted 08/05/21 12:19 AM Doing any head work? Porting the exhaust side theoretically helps spool. Always wondered what results Higgins or the like would get with Barra heads. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now