Jump to content

Where in the 300s will this end up?


karlp2

Recommended Posts

  • Member
  • Member For: 11y 4m 10d
  • Gender: Male
  • Location: Auckland, New Zealand

Where in the 300s will these mods get my G6ET on 98 fuel:

Walbro 400 (already fitted)

1000cc injectors (to be fitted)

PW stage 1 intercooler and piping (already fitted)

X-force - full system with the twin 2.5 pipes (already fitted)

GTX3582R gen2 with modded exhaust housing (36mm flapper, porting etc), and 14psi actuator.  Just picked up last week, to be fitted.

Tune being done on a roller dyno, will be go in the next few weeks when the tuner is free.  Thanks

Link to comment
Share on other sites

  • 4 weeks later...
  • Member
  • Member For: 11y 4m 10d
  • Gender: Male
  • Location: Auckland, New Zealand

Got car back fromtuner, achieved 355rwkw and 802nm, suffered bad heat  soak with follow up runs typically dropping 30rwkw.  Not too sure that the car feels that much different to drive over the old mods.  Definitely sounds better with the huge induction noise and turbo whine but just not quite going as well as I’d anticipated, not sure what to do next

Link to comment
Share on other sites

  • Puff
  • Gold Donating Members
  • Member For: 9y 10m 28d
  • Gender: Male
  • Location: South Australia

Upgrade to the largest intercooler you can afford. The gen 2 is much lazier than a stock turbo, so until it gets turned up to 20+psi, it'll probably feel like a waste of time.

At least you have a decent actuator on there, so it'll be as responsive as it can be.

Wait for a cool day and see what you think, heat soak is a real power killer.

Link to comment
Share on other sites

  • FREAKY
  • Donating Members
  • Member For: 15y 2d
  • Gender: Male
  • Location: Melbourne

sounds like its pretty linear tune

 

I would expect 400 on 98. but there must be something holding it back or tuner is playing safe to not grenade your engine. 

 

I wouldnt say heat soak in NZ is that much of an issue but the stage 1 is not that bad. 

Link to comment
Share on other sites

  • Donating Members
  • Member For: 9y 4m 25d
  • Gender: Male
  • Location: NZ

My friend has his FG XR6T tuned at CTB, Made 270rwkw on their dyno then 310rwkw on a hub dyno so might sound lower than it actually is. Maybe you could try torque performance? I found Sam at CTB too busy to chat when I discussed having my car tuned there so decided against them. 

Link to comment
Share on other sites

  • ...JD TUNING ADELAIDE...
  • Gold Donating Members
  • Member For: 16y 6m 26d
  • Gender: Male
  • Location: Adelaide

What in the chit crap is that !!

 

no wonder you’ve got heat soak as he’s smashing in over 20psi on the hit and clearly way too much timing up top that it’s being reduced for the IAT’s 

 

You NZ’ers need new tuners that know how to work falcons 

 

20kmh/sec is for like 500+ hi stalled vehicles for christ sake 

 

you combo would suppprt around 14psi to make ~350 efficiently and correctly especially with a stage 1 cooler kit 

 

bloody Derp 

Edited by JETURBO
  • Like 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
  • Create New...
'