Jump to content

CPV tuned FG F6


sprouly07

Recommended Posts

  • Donating Members
  • Member For: 10y 4m 8d
  • Gender: Male
  • Location: Townsville

So a couple months ago the turbo on my f6 failed so it needed to be replaced. I had been talking to Dave from CPV Tuning for a couple months about upgrading the turbo and when the stock turbo failed it kind of forced my hand and the turbo was upgraded. Hadn't planned on doing it this early but couldn't see the point in replacing the stock turbo and then getting a  new one again in 6 months time.

 

So a custom turbo from monsta torque was ordered and installed to go along with existing mods like manta exhaust, twin 460 surge tank, intanke 460, PW stage 3 cooler, valve springs, 1000cc injectors and stall converter. The daily tune ended up doing 459.6kw and the drag tune ended up going 493.4kw, both were on e85

  • IMG_4421.JPG

IMG_4422.JPG

 

 

 

 

 

 

Most impressive thing about the car is that it still retains the standard airbox and intake so there is no doubt in my mind that if a turbo side intake was installed than the car would make over 500rwkw but that's not what I was chasing with this car. I wanted to keep a relatively standard looking engine bay seeing as though it is still my daily so to the untrained eye it would still look standard and I wouldnt get much attention. I also wanted to see if it was possible to run a 9 on the standard intake so will hopefully get a chance to go down the strip soon and see what time it does.

IMG_4582-2.jpg

  • Like 8
Link to comment
Share on other sites

  • Donating Members
  • Member For: 10y 4m 8d
  • Gender: Male
  • Location: Townsville

They seem to keep it fairly quiet though. I've had turbo Falcons for about 3 years now, with the last one being a bf and it wasn't till I got the f6 and started talking to Dave that I even heard about this turbo. So they have done well on keeping it a bit of a secret.

But I have seen on Facebook a company called RaceEquipped doing a very similar turbo now. They call it a high flow gt35 which has a 66mm

Link to comment
Share on other sites

  • MattyP
  • Cruise Control
  • Member For: 12y 6m 17d
  • Gender: Male
  • Location: Central Coast

Mamba and Kinugawa have been doing it for a while as well. Jim gianna, race equipped and another Aussie company do them here locally 

 

is your one in the .7 cover?

Link to comment
Share on other sites

  • Donating Members
  • Member For: 10y 4m 8d
  • Gender: Male
  • Location: Townsville

Yeah alright, first time I've ever heard of a company doing it was monsta torque. Do they all perform roughly the same?

I had always been pushed towards a gtx or a precision.

Yeah mine has the .7 cover.

Link to comment
Share on other sites

  • Donating Members
  • Member For: 13y 7m 11d
  • Gender: Male
  • Location: Perth

With a good set of slicks, and a upgraded converter you'll manage a 9sec pass. I did it in my FG XR6, with the same turbo from Rob. It's kept so quiet because everyone talks about the GTX3582r and don't want to hear at the the 66mm with .7'cover.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
  • Create New...
'