Guest Guests Posted 01/08/16 07:25 AM Share Posted 01/08/16 07:25 AM (edited) the one in the link above is only slightly bigger @ 62.5mm so id say stage 2. A 66mm would be on par with a T04Z in the factory location though Edit:- confirmed T04Z is .5mm bigger below than a stage 3 66mm rebuild Compressor wheel: 66.5/84 mm Edited 01/08/16 07:27 AM by mightbuyaford Link to comment Share on other sites More sharing options...
molch Donating Members 174 Member For: 18y 6m 29d Gender: Male Location: Central Coast Posted 01/08/16 07:56 AM Author Share Posted 01/08/16 07:56 AM 44 minutes ago, mightbuyaford said: stage 33 66mm wheel can go in a modded 3" housing or go for a .7 4" 66mm is 5mm oversize and is good for 500wkw if you want to rebuilt a standard turbo otherwise kinugawa/mamba are great value for money but might cost a little more in the end with mods to exhaust etc if you go a full turbo.. both good options Thanks for all the responses guys.. So many options that's it's hard to make a final decision. What mods to the exhaust are required for the Mamba bolt on turbo? Also so who do you guys recommend for a rebuild if I go down that path? also I am 99% sure I'm going to get CMS to do the tune. Link to comment Share on other sites More sharing options...
MattyP MattyP Cruise Control 6,317 Member For: 12y 9m 25d Gender: Male Location: Central Coast Posted 01/08/16 08:04 AM Share Posted 01/08/16 08:04 AM I'd rather go a new complete turbo tbh No mods to the exhaust,Cms is good tip top Link to comment Share on other sites More sharing options...
Guest Guests Posted 01/08/16 08:04 AM Share Posted 01/08/16 08:04 AM whats the end game of the car? power figure? the mamba linked above has a V band rear housing so you would either need to change the housing or get a new dump pipe fabbed. nick from RE in melbourne would be good. He does rebuilds for about $950 - $1500 and will ship it back to you with new studs and ceramic coating free of charge Link to comment Share on other sites More sharing options...
molch Donating Members 174 Member For: 18y 6m 29d Gender: Male Location: Central Coast Posted 01/08/16 08:28 AM Author Share Posted 01/08/16 08:28 AM (edited) Ok gotcha. So the the gtx 3584r from mamba had the standard bolt rear housing so that's the winner. https://www.ebay.com.au/itm/181896660191 I think I'm leaning this way, now just need to decide if I go the bigger housing. Will pm him and see if it changes the pricing much. Then I just need to worry about a single silicon intake pipe from the relocated intake... The turbo spool up was already pretty noisy, can't imagine it louder with a 4" intake. Edited 01/08/16 08:31 AM by molch Link to comment Share on other sites More sharing options...
Guest Guests Posted 01/08/16 08:39 AM Share Posted 01/08/16 08:39 AM that's a direct bolt on. No need to change it unless you really want a 4" inlet but already has an A/R7 housing just with the 3" inlet Compressor Housing Inlet OD: 3” / 76.2mm Compressor Housing Outlet OD: 2” / 51 mm Compressor Housing A/R: .70 Turbine Housing A/R : 1.05 Link to comment Share on other sites More sharing options...
MattyP MattyP Cruise Control 6,317 Member For: 12y 9m 25d Gender: Male Location: Central Coast Posted 01/08/16 10:43 AM Share Posted 01/08/16 10:43 AM Yup that's the bolt on one That's a .5 compressor cover damo, .7 is the big one for the horny turbo whistle Link to comment Share on other sites More sharing options...
Guest Guests Posted 01/08/16 10:47 AM Share Posted 01/08/16 10:47 AM I didnt really look just noticed it was a 3" inlet but specs say an .7 cover lol Link to comment Share on other sites More sharing options...
molch Donating Members 174 Member For: 18y 6m 29d Gender: Male Location: Central Coast Posted 01/08/16 08:55 PM Author Share Posted 01/08/16 08:55 PM Dodgy advert! Anyway I messaged him last night asking if he will mate it to a 4" inlet with 0.7 a/r. Waiting response. I think today ill book in CMS and a day off work for the trip down in a couple of weeks. Link to comment Share on other sites More sharing options...
sixman Donating Members 601 Member For: 20y 7m 7d Gender: Male Location: Hills District, NSW Posted 02/08/16 06:02 AM Share Posted 02/08/16 06:02 AM If your going to cms, chat to them before buying anything. They will give you lots of good options that they can make work. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now