frozenxr6t Member 140 Member For: 10y 3m 27d Posted 08/08/15 09:35 AM Share Posted 08/08/15 09:35 AM and news on the new setup Link to comment Share on other sites More sharing options...
747pwr Member 68 Member For: 13y 9m 1d Gender: Male Posted 08/08/15 02:01 PM Author Share Posted 08/08/15 02:01 PM I work away so nothing happening this week- get back mid week and will be picking up new housing and turbo to assemble and put it all back together - hopefully tuned before the weekend Link to comment Share on other sites More sharing options...
Bomber Carnage on the Garage Floor Donating Members 3,994 Member For: 14y 7m 1d Gender: Male Location: Gold Coast Posted 11/08/15 09:03 AM Share Posted 11/08/15 09:03 AM I couldn't get mine to make less than 18psi Link to comment Share on other sites More sharing options...
747pwr Member 68 Member For: 13y 9m 1d Gender: Male Posted 12/08/15 11:14 AM Author Share Posted 12/08/15 11:14 AM (edited) That's common if your port job is dodgyFitted the new set up today - hopefully tuned tomorrow or Friday Edited 12/08/15 11:22 AM by 747pwr 1 Link to comment Share on other sites More sharing options...
747pwr Member 68 Member For: 13y 9m 1d Gender: Male Posted 13/08/15 03:20 AM Author Share Posted 13/08/15 03:20 AM Picture of the bay yesterday after installing the gtx3582 dropped it off for a tune this morning on 98.Initial thoughts - this thing is quiet and wasn't feeling much torque under 3000rpm - mind you was only cruising to the workshop. Link to comment Share on other sites More sharing options...
JETURBO ...JD TUNING ADELAIDE... Gold Donating Members 23,708 Member For: 16y 6m 11d Gender: Male Location: Adelaide Posted 13/08/15 03:43 AM Share Posted 13/08/15 03:43 AM Mate the 76 and 82 are a noticeable step apartWe did try to tell you 2 Link to comment Share on other sites More sharing options...
747pwr Member 68 Member For: 13y 9m 1d Gender: Male Posted 13/08/15 03:47 AM Author Share Posted 13/08/15 03:47 AM Yeah I'm not saying it's bad - I wanted the power to shift higher In the revs, the 76 fell over to early for MY liking Link to comment Share on other sites More sharing options...
BenDoCo I'm getten too old for this s**t Bronze Donating Members 4,509 Member For: 11y 8m 5d Gender: Male Location: A big bridge over a river in South Australia Posted 13/08/15 04:15 AM Share Posted 13/08/15 04:15 AM Ya shoulda told ya tuna to fix it then but no matter now as I see that some very lucky person now has a 76.Congrats - whoever bought it Link to comment Share on other sites More sharing options...
747pwr Member 68 Member For: 13y 9m 1d Gender: Male Posted 13/08/15 04:54 AM Author Share Posted 13/08/15 04:54 AM Wasn't the tuners fault - last tuning session cut short due to a boost issue/mechanical problem so tuned best we could - got bored one day and started this thread - got some good advice and found the problem, always wanted the bigger turbo and once the 76 sold the swap cost me a couple hundred plus the tune, car was apart and had to retune anyway was kind of two birds one stone. Link to comment Share on other sites More sharing options...
747pwr Member 68 Member For: 13y 9m 1d Gender: Male Posted 14/08/15 11:04 AM Author Share Posted 14/08/15 11:04 AM Was on dyno today briefly, under boosting sorted, now over boosting issue with new turbo/housing/wastegateDialed in 17psi would make it until 3800 then 20psi by 5000 till red lineI bench tested the actuator would open at 15psi on any preload setting, I set the preload to about 3mm used to compressor to push rod onto waste gate, which was the least preload to make the valve not spin on the housing when I tried. Could still move the actuator rod by hand if hanging off it, way easier than the turbo smart set upBut I read they use much less preload than the turbo smart part.The flapper valve is a 38mm item and we ported it slightly smaller than previous housing to try keep some more meat to prevent cracking this one.Does it sound like I set the actuator up right ? Good chance I'll have to pull off housing and open port up some more ? It was d-shaped like shown on here.Guess I'll be in shed all weekend But it did make 400rwkw on 98, reduced timing 17psi building to 20. Which is a start haha Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now