First Turbo New Member 7 Member For: 10y 3m 29d Gender: Male Location: Perth Posted 07/04/15 01:17 PM Share Posted 07/04/15 01:17 PM I'm about to fit the 328 mm rear brakes to my FG ute, two questions. Do I need a new bracket for the calipers or will the old one do.Also does anyone have recommendations for some good braided lines for the setup? Link to comment Share on other sites More sharing options...
GeGe6 Donating Members 1,978 Member For: 12y 5m 14d Gender: Male Location: Perth, SOR Posted 07/04/15 01:21 PM Share Posted 07/04/15 01:21 PM Matt from Race Brakes Sydney for braided lines.As for PBR upgrades my went straight on. Link to comment Share on other sites More sharing options...
GeGe6 Donating Members 1,978 Member For: 12y 5m 14d Gender: Male Location: Perth, SOR Posted 07/04/15 03:36 PM Share Posted 07/04/15 03:36 PM Forgot to mention you will need to cut the backing plate.Not a hard job. 1 Link to comment Share on other sites More sharing options...
discostig Manual mode ________________________ All day, erryday Donating Members 13,798 Member For: 17y 27d Gender: Male Location: Probably above atmospheric pressure Posted 08/04/15 05:22 AM Share Posted 08/04/15 05:22 AM Yeah that's an important point. I thought it looked OK when I fitted mine and drove around with a funny squeal for a few days, only audible from in car when next to walls at first so I thought it was sweet on the evening test drive in the hills where I live. Made a nice score on the rotor! Link to comment Share on other sites More sharing options...
First Turbo New Member 7 Member For: 10y 3m 29d Gender: Male Location: Perth Posted 24/04/15 02:22 AM Author Share Posted 24/04/15 02:22 AM Cheers Guys Link to comment Share on other sites More sharing options...
MitchJ New Member 8 Member For: 4y 3m 25d Posted 01/09/20 06:53 AM Share Posted 01/09/20 06:53 AM Thought I'd post here instead of opening a new thread, I understand you need to trim the backing plate on the rears prior to installing the PBR calipers. Just wanted to query what this thing actually does and how much I should be looking to take off it? Like, if I cut it with 5mm clearance to the caliper have I gone too far or if I leave 5mm of it left on the axle have I not cut back far enough? Link to comment Share on other sites More sharing options...
El Andrew Gold Donating Members 2,036 Member For: 9y 7m 29d Gender: Male Location: Canberra ACT Posted 01/09/20 12:03 PM Share Posted 01/09/20 12:03 PM The backing plate and caliper don't move in relation to each other so you don't need heaps of clearance. 5-10mm is probably pretty good. You just don't want much opportunity for a rock to get wedged in there.Then just file of the sharp edge and give it a squirt with paint to prevent rust.Thought I had a pic of mine but can't find it unfortunately. Link to comment Share on other sites More sharing options...
MitchJ New Member 8 Member For: 4y 3m 25d Posted 04/11/20 08:47 AM Share Posted 04/11/20 08:47 AM Hey guys, had the PBR upgrade fitted as part of a service today and have now subsequently had an issue with the DSC. When I accelerate hard to break traction, the DSC will intervene but then in five seconds or so will register a fault and show the warning light on the dash. If I turn the car off the warning light goes away, but the error will re-appear if the DSC has to intervene again. Is there a calibration that's required to be completed after installing the PBRs? I'm assuming that the DSC may not be seeing the response that it's inputs are programmed to achieve due to the bigger brakes and is showing a warning because of that. Brake set up was PBR rear calipers + DBA T3s + Project MU pads and it's on an FG MKII Turbo sedan. Link to comment Share on other sites More sharing options...
k31th less WHY; more WOT Site Developer 29,043 Member For: 16y 8m 11d Gender: Male Location: Melbourne Posted 04/11/20 09:55 AM Share Posted 04/11/20 09:55 AM Yeah, your DSC calibration is off now that you've changed the brakes. Just turn the DSC off if you're going to break traction and leave DSC to handle it when you're not intending to break traction. 1 Link to comment Share on other sites More sharing options...
MitchJ New Member 8 Member For: 4y 3m 25d Posted 04/11/20 10:09 AM Share Posted 04/11/20 10:09 AM Thanks mate, was worried that was going to be the answer haha If I went all out and got a set of 4 pot Brembos on the front to match the set up on HWP cars, how easy is it to re-calibrate the DSC? Assuming Ford has a unique calibration for that set up. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now