Jump to content

Noturbo's Donkey


JETURBO

Recommended Posts

  • ...JD TUNING ADELAIDE...
  • Gold Donating Members
  • Member For: 16y 7m 9d
  • Gender: Male
  • Location: Adelaide

Yeh matty a 3037 iirc but theres choices left right and centre on sizes and what u want from them and boost is almost at idle choice dependant

Edited by Butt Plug
Link to comment
Share on other sites

  • I'm getten too old for this s**t
  • Bronze Donating Members
  • Member For: 11y 9m 2d
  • Gender: Male
  • Location: A big bridge over a river in South Australia

I'm still a believer of TT on a v8 .... my only reason is that 1 each bank seems right to me.

What has to be done to lower compression?

Or should I be asking

Do you need to lower compression with a big single?

Edited by BenDoCo
Link to comment
Share on other sites

  • Dropping a turd
  • Gold Donating Members
  • Member For: 17y 2m 13d
  • Gender: Male
  • Location: Perth

Its deceiving matty its a fairly big unit

And that's higher than what I thought barnz I was thinking 250rwkw

My car is at 250rwkw. I think the 325 go about 250 and 340 a bit more

Link to comment
Share on other sites

  • ...JD TUNING ADELAIDE...
  • Gold Donating Members
  • Member For: 16y 7m 9d
  • Gender: Male
  • Location: Adelaide

that's just page set up barnz rpm for ftlb would be same/same and dont forget the engine cover is best part wank but done on a engine dyno not a chassis dyno with transmissions doing things to outputs

Arron in that vid the 340 went 263rwkw .... Not bad honestly

Edited by Butt Plug
  • Like 1
Link to comment
Share on other sites

  • ...JD TUNING ADELAIDE...
  • Gold Donating Members
  • Member For: 16y 7m 9d
  • Gender: Male
  • Location: Adelaide

I'm still a believer of TT on a v8 .... my only reason is that 1 each bank seems right to me.

What has to be done to lower compression?

Or should I be asking

Do you need to lower compression with a big single?

The LS3 runs some of the highest comps going in the Expensive Daewoo and yes it does become a factor but it has alot to do with the density of the psi and then what you do tune related after that, a cam has its place in any engine hence the term "blower cam" or "turbo cam"

Link to comment
Share on other sites

  • Donating Members
  • Member For: 11y 7m 15d
  • Gender: Male
  • Location: NOR Perth
  • I'm getten too old for this s**t
  • Bronze Donating Members
  • Member For: 11y 9m 2d
  • Gender: Male
  • Location: A big bridge over a river in South Australia

I did read about 'turbo cams' on one of the yank forums.

Thinking about it now :) I understand a bit of what they were talking about..

I'll try and find that page again and have another read............cheers

Edit

I like those Slippers ^^^

Edited by BenDoCo
  • Like 1
Link to comment
Share on other sites

  • ...JD TUNING ADELAIDE...
  • Gold Donating Members
  • Member For: 16y 7m 9d
  • Gender: Male
  • Location: Adelaide

Errybody jelly cept lukey #suedebutnotsuede

Don could go on about cams till iam as old as you but it can be weird to understand for some

  • Like 2
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
  • Create New...
'