Jump to content

Autotech Tuned Fg


Seaton

Recommended Posts

  • WOT?
  • Moderating Team
  • Member For: 11y 11m 29d
  • Gender: Male
  • Location: Frankston, 3199

Are you saying Spiro held back on the first run to show a lower number???

So the final result is more impressive???

That's not how he works mate and he does not care about final figures, it's all about how the car performs.

Not at all - should have worded the post differently. I do apologies if it looked like I was casting aspersions. Was late at night and a few beers down so wasn't wording my posts with much afterthought.

Just saying the car was reading lower on the initial run than the 113mph pass would account for and that the final figure was probably about the correct output for the mods done indicating that the dyno isn't giving substantially lower results.

Limp right foot was the wrong thing to suggest - could be any number of reasons for it.

  • Like 3
Link to comment
Share on other sites

  • Donating Members
  • Member For: 12y 5m 27d
  • Gender: Male
  • Location: Sydney

Don't forget the car had a few parts bolted on already when I delivered the car. They had to finish the rest for me.

The figures mean little to me. The car feels strong as.

And so smooth. I took a few guys for runs in it from work yesterday, one with a modded S15. They were all super impressed, and could not believe how smooth it is.

It feels better than I had expected.

Link to comment
Share on other sites

  • WOT?
  • Moderating Team
  • Member For: 11y 11m 29d
  • Gender: Male
  • Location: Frankston, 3199

You should definitely be wrapped and proud of what's been achieved :)

The extra parts bolted on could well explain why it wasn't pulling stronger before remainder and the tune :)

  • Like 1
Link to comment
Share on other sites

  • Member
  • Member For: 12y 1m 15d
  • Gender: Male
  • Location: Wollongong

I have run a 1.13 around there, keep in mind I am quite new to this so I am hoping next year I can get that down a bit more, one of the other guys here is down to a low 1.08.

That's pretty good man. We're only doing 1:05's - 1:06's depending on tyres and temperature. The faster guys are dipping into 1:03's on the 600's. I know the pro's are doing 0:58's on the 1000cc Australasian superbikes. My boss has one of the radical track cars and I'm pretty sure he hovers around the 59 - 1:00

Link to comment
Share on other sites

  • Donating Members
  • Member For: 13y 6m 12d
  • Gender: Male

the fg 113 mph and my ba 112 mph . but both of our 60"were in the 2 seconds .ps both are automatics fg 6 speed and mine a 4 speed .and none had wheel spin

Strange, brothers bf with zf 6spd ran 11.0 with 340rwkw but he's 60ft was 1.6!!! 2.0 is crazy slow 60ft!!!

Edited by Kosij
  • Like 1
Link to comment
Share on other sites

  • Donating Members
  • Member For: 12y 5m 27d
  • Gender: Male
  • Location: Sydney

Yeah I have been getting comments on how good it sounds.

It does need a few further tweaks, it really is a massive exhaust and it slightly hits the cradle at the moment.

Also, it slightly drones with the zf as you now hear the gear changes and the car almost drives around in 6th gear most the time.

Worst case, I will buy the valve and put it in as I have a 3yo I take away in the car and it might be worse in the back seat.

I'll see how we go, it might get a touch better as it carbons up a little over time.

Edited by Seaton
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
  • Create New...
'