ratter Member 6,793 Member For: 18y 6m 17d Gender: Male Location: @ my laptop Posted 27/08/14 09:49 AM Share Posted 27/08/14 09:49 AM do not get sucked into a high powered car assuming they must know what they are doing, power is easy to get with the right combination, driveability, good manners and correct ecu control can be totally different and an area that it seems many fail in.I have no idea about the shop in question or their abilities 3 Link to comment Share on other sites More sharing options...
genuine honest person Member 2,769 Member For: 10y 10m 16d Gender: Male Location: near brisbane Posted 27/08/14 10:01 AM Author Share Posted 27/08/14 10:01 AM (edited) I will see tomorrow how it goes (he may have it up and running ) thanks for the help valve springs will be next . How much are they to get done ,by a reputable person in brisbane or sunshine coast . thanks again Edited 27/08/14 10:04 AM by gunna Link to comment Share on other sites More sharing options...
old_mate Member 767 Member For: 18y 10m 1d Gender: Male Location: Brisbane Posted 27/08/14 11:20 AM Share Posted 27/08/14 11:20 AM I think clinton at ProFile charged me 800 ish for atomics installed? this was a couple of years ago now. 1 Link to comment Share on other sites More sharing options...
discostig Manual mode ________________________ All day, erryday Donating Members 13,798 Member For: 17y 20d Gender: Male Location: Probably above atmospheric pressure Posted 27/08/14 01:43 PM Share Posted 27/08/14 01:43 PM Yeah that sounds fair. XFT are $900 supply and fit in WA I think. Got a few things done at the same time. 1 Link to comment Share on other sites More sharing options...
camo86T Silver Donating Members 1,810 Member For: 10y 10m 2d Gender: Male Location: SW Sydney Posted 27/08/14 10:18 PM Share Posted 27/08/14 10:18 PM CMS quoted me $800 supplied and fitted the other day, not sure what brand though 1 Link to comment Share on other sites More sharing options...
Kimberley Scott www.australianflag.org.au Donating Members 6,763 Member For: 19y 4m 27d Gender: Male Location: Brisbane Posted 27/08/14 10:24 PM Share Posted 27/08/14 10:24 PM Gunna you strike me as capable of changing your own valve springs. Personally never done it. So maybe seek advice from those that have. 1 Link to comment Share on other sites More sharing options...
AzMahoony Hench, but no longer shredded or tanned. Member 3,343 Member For: 17y 8m 16d Gender: Male Location: Canning Vale, W.A Posted 27/08/14 11:07 PM Share Posted 27/08/14 11:07 PM Aint the tool only a few $$$ squiddies on ebay? 1 Link to comment Share on other sites More sharing options...
barnz Member 3,047 Member For: 11y 24d Gender: Male Location: Brisbane Posted 28/08/14 01:15 AM Share Posted 28/08/14 01:15 AM You will be right gunna, only takes 30 mins... 1 Link to comment Share on other sites More sharing options...
genuine honest person Member 2,769 Member For: 10y 10m 16d Gender: Male Location: near brisbane Posted 28/08/14 06:54 AM Author Share Posted 28/08/14 06:54 AM (edited) ok I have some better news today . The ute used to have 872 nm and now not completely tuned has 1344 nm that is 472 nm more .The only braw back is the valve springs are gonesoft ,so the power drops like a sinking boat at 5000 rpm and only produces 275 rwkw . Craig the owner was not there no more so was unable to talk to him ,but the guys said that hewill get it all sorted in the morning .So wish me luck that everything works out .looking at the graph the improvement in torque starts right down low ,so my 60" would have to be a lotbetter now .They also said that the E Boost fixed the problem straightaway . Had a look at the injector duty cycle and they were up to 49% and they are Bosch 1000 ,so the 440 Bosch injectors may have been on there limit ?ps ,if I would change the valve springs . I would have to take out the cam shafts and timing chain ? that may just be a bit advanced for my skills . this tuner wants over $900 to fitthem up . there is a engine rebuilder in our street (reagan engines ) I might ask him for a price . Or am I better of going to the professionals like profile ?what are some good valve springs that will last and do there job well ? thanks . Today I feel relived that the money that I have handed over may have been worthwhile . If I could only have $1000 dollars more I would just bite the bullet and get the valve springs done ,but I am maxed out and have nothing left .But if I changeat 5000 rpm it will be fine for now Edited 28/08/14 07:01 AM by gunna 1 Link to comment Share on other sites More sharing options...
JETURBO ...JD TUNING ADELAIDE... Gold Donating Members 23,708 Member For: 16y 6m 13d Gender: Male Location: Adelaide Posted 28/08/14 06:59 AM Share Posted 28/08/14 06:59 AM Monkeys can do valve springs Would of left the tuning to the professional Just saying I think u should have a suss at what torque "figures" on dyno read out means for real life torque figures Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now