ramp rate Member 49 Member For: 10y 7m 4d Gender: Male Location: central coast nsw Posted 02/08/14 11:25 AM Share Posted 02/08/14 11:25 AM SHOWTYM DETAILING BA XR6T 344RWKW, STOCK BOTTOM END,PLAZAMAN VALVE SPRINGS, ATOMIC OIL PUMP GEARS, ATOMIC FLEX PLATE, 4INCH DUMP, DUAL 3INCH CAT BACK,CENTER AND REAR MUFFLERS, CUSTOM CAI, STOCK GT3540 TURBO, PLAZAMAN BILLET FUEL RAIL,BOSCH 1000CC INJECTORS, TUNED BY TUFF TUNE PERFORMANCE, EASY 344RWKW @4750 /830NM ON 10PSI ,NOT GOING TO PUSH IT UNTIL NEW FORGED MOTOR IS FINISH IN THE NEXT FEW WEEKS. THEN ADD BOOST TO AROUND 15PSI AND SEE WHAT THE DYNO AND WHAT NUMBERS WE CAN RUN DOWN THE 1/4 ON OLD BA STOCKER BOTTOM END CAN TAKE Link to comment Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,331 Member For: 19y 5m 8d Gender: Male Location: Perth Posted 02/08/14 11:31 AM Share Posted 02/08/14 11:31 AM Well that's easy to read. Link to comment Share on other sites More sharing options...
ramp rate Member 49 Member For: 10y 7m 4d Gender: Male Location: central coast nsw Posted 02/08/14 11:37 AM Author Share Posted 02/08/14 11:37 AM that's THE BEST IVE GOT NOT TO COMPUTOR SAVY 1 Link to comment Share on other sites More sharing options...
genuine honest person Member 2,769 Member For: 11y 1m 3d Gender: Male Location: near brisbane Posted 02/08/14 12:00 PM Share Posted 02/08/14 12:00 PM that's a lot of rwkw for only 10 psi ?will not believe you unless I see dyno sheet .I am running 12 psi and only have 280 rwkw and 869 nm Link to comment Share on other sites More sharing options...
genuine honest person Member 2,769 Member For: 11y 1m 3d Gender: Male Location: near brisbane Posted 02/08/14 12:02 PM Share Posted 02/08/14 12:02 PM maybe due to dump pipe and bigger exhaust ? Link to comment Share on other sites More sharing options...
MattyP MattyP Cruise Control 6,317 Member For: 12y 9m 27d Gender: Male Location: Central Coast Posted 02/08/14 12:05 PM Share Posted 02/08/14 12:05 PM 7 Link to comment Share on other sites More sharing options...
Rab WOT? Moderating Team 10,981 Member For: 12y 6d Gender: Male Location: Frankston, 3199 Posted 02/08/14 12:23 PM Share Posted 02/08/14 12:23 PM $2,400,399.00 EXILED FOR YOU - ERROR ON OIL PRINCES TRUSTEE WILL.HE DIED - NO BENEFICIARIES SEND $45 AND BANK DETAILSKEEP SECRET - TELL NO ONE100% HONEST 4 Link to comment Share on other sites More sharing options...
genuine honest person Member 2,769 Member For: 11y 1m 3d Gender: Male Location: near brisbane Posted 02/08/14 12:44 PM Share Posted 02/08/14 12:44 PM I must be wrong ,but 10 psi and 344 rwkw wow I am envies over that 1 Link to comment Share on other sites More sharing options...
JVK Silver Donating Members 751 Member For: 19y 2m 13d Gender: Male Location: North West Hot Hell,VIC Posted 02/08/14 10:49 PM Share Posted 02/08/14 10:49 PM Im with gunna, Top result for ramp rate if it is correct but I don't think with that hardware 344@10psi is possible.Unless the op left a little out like Nizpro plenum and E85 fuel and tune. Dyno sheet pic would be good for proof. 1 Link to comment Share on other sites More sharing options...
ramp rate Member 49 Member For: 10y 7m 4d Gender: Male Location: central coast nsw Posted 03/08/14 08:09 AM Author Share Posted 03/08/14 08:09 AM all true will get my you bloke to upload dyno print out in next 24hrs im abit on the backward side when it come to computors,zero tricks tuned and run on 98octane,I did forget also running aftermarket industry surge with dominator 900hp in surge pump plus walbro 044 intake pump, no trick intake or e85,that's all on the new forged engine.just rip a spot on tune in it and let it rip. 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now