.Stripes. All stock bar the k&n panel filter Silver Donating Members 8,061 Member For: 12y 9m 30d Gender: Male Location: Perth Posted 25/03/16 04:07 AM Share Posted 25/03/16 04:07 AM Thread needs moar photos of your feet. Link to comment Share on other sites More sharing options...
genuine honest person Member 2,769 Member For: 10y 11m 15d Gender: Male Location: near brisbane Posted 25/03/16 05:22 AM Author Share Posted 25/03/16 05:22 AM whats wrong with my new thongs? They run at 15 psi at the moment 3 Link to comment Share on other sites More sharing options...
arronm Dropping a turd Gold Donating Members 9,520 Member For: 17y 2m 16d Gender: Male Location: Perth Posted 25/03/16 05:39 AM Share Posted 25/03/16 05:39 AM Low performance single plugers. 1 Link to comment Share on other sites More sharing options...
genuine honest person Member 2,769 Member For: 10y 11m 15d Gender: Male Location: near brisbane Posted 25/03/16 07:47 AM Author Share Posted 25/03/16 07:47 AM cut that lump of today that was on the air intake .also cit the pipes to suit Will be able to get them welded .tommorow the 3 inch cold side will be my main goal to get fitted up redy for welding On 25/03/2016 at 3:07 PM, .Stripes. said: Thread needs moar photos of your feet. as you asked. would love somthing simular I would appreciate some input on this ,can I get some arp or simular washers to suit .as the bolt is 8 mm and the dump pipe holes are 10.5 .I will make some shims to locate the dump in the centre can see day light Link to comment Share on other sites More sharing options...
arronm Dropping a turd Gold Donating Members 9,520 Member For: 17y 2m 16d Gender: Male Location: Perth Posted 25/03/16 09:04 AM Share Posted 25/03/16 09:04 AM Yes use washers. Stainless would be best. They don't need to be anything special. Just make sure they are a close fit to the bolt. The 10.5 mm hole probably reflects the fitting tolerance in the flange. The flow area is large so I wouldn't worry to much about matching the fit. 1 Link to comment Share on other sites More sharing options...
genuine honest person Member 2,769 Member For: 10y 11m 15d Gender: Male Location: near brisbane Posted 25/03/16 11:27 AM Author Share Posted 25/03/16 11:27 AM Thanks for that .I will try to get some about 3 mm thick so they do not bent to easely Absolutely gutted as I have had a look at the an 6 fittings and they are way to small to use ,it should have been an 8 fittings .dominello said to use an 6 .what a f*ck up . what a set back this is .I even said to him I would rather use an 8 as it travels further than the standard set up .the an 6 size of the bends are like 5 mm at the most and the standard steel line is 7 to 8 mm . Now that will cost me again .he better send that box to me next week or I will cancel it as it was paid in full last easter . Link to comment Share on other sites More sharing options...
genuine honest person Member 2,769 Member For: 10y 11m 15d Gender: Male Location: near brisbane Posted 25/03/16 02:35 PM Author Share Posted 25/03/16 02:35 PM Must be these proflow fittings that are the problem as the speedflow do not reduce in size . Link to comment Share on other sites More sharing options...
arronm Dropping a turd Gold Donating Members 9,520 Member For: 17y 2m 16d Gender: Male Location: Perth Posted 25/03/16 03:17 PM Share Posted 25/03/16 03:17 PM For my engine oil cooler and trans cooler I used -10AN. Anything else is to small. Return the lot and and get -10 push on fittings and 400 series hose 1 Link to comment Share on other sites More sharing options...
genuine honest person Member 2,769 Member For: 10y 11m 15d Gender: Male Location: near brisbane Posted 25/03/16 09:21 PM Author Share Posted 25/03/16 09:21 PM Might go an 8 as everyone comments on another forum that 6 is the cirect size but the cheap fittings is what the problem is .they say not to go bigger due to line presure ? Going to phone domminelo on tuesday and ask again ,and want also a deffenet answer when the box will be here . he never replies what I ask him .most of the time I have to phone and get answers, and then I have to phone several times to get him . Link to comment Share on other sites More sharing options...
arronm Dropping a turd Gold Donating Members 9,520 Member For: 17y 2m 16d Gender: Male Location: Perth Posted 26/03/16 02:51 AM Share Posted 26/03/16 02:51 AM I have sent you a PM 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now