arronm Dropping a turd Gold Donating Members 9,520 Member For: 17y 2m Gender: Male Location: Perth Posted 19/04/14 11:36 AM Share Posted 19/04/14 11:36 AM The compressor wheels have the tendancy of flying apart at those kind of figures. Chancing a lot of bits flying through the whole systemOnly 17 psi as Ralph said and tapering down to 15 to 13. Turbo will be sweet,, The only thing flying apart will be the tyres. 1 Link to comment Share on other sites More sharing options...
MattyP MattyP Cruise Control 6,317 Member For: 12y 7m 23d Gender: Male Location: Central Coast Posted 19/04/14 12:09 PM Share Posted 19/04/14 12:09 PM Any plans on a new turbo? Link to comment Share on other sites More sharing options...
puck_lindsay New Member 21 Member For: 11y 7m 23d Gender: Male Location: Perth, WA Posted 19/04/14 06:42 PM Author Share Posted 19/04/14 06:42 PM BenDoCo- cost $500, could've done a turbo side intake cheaper with better performance. Works well for what it is, but wouldn't buy on again. FiftyOne - thanks for the concern, think the bearings will fail before the compressor wheel though. Hopefully a while before that happens. Arronm - definitely need wider/stickier rears =PP91 - not for the moment, if I'm honest current power levels exceed my skill level, working on handling mods and getting some experience. I'm also 20hp off the maximum power recommended for the diff and 250nM more torque than the gearbox is rated to, so if I push the ceiling much further, I will have a huge bill on my hands. If I have to change turbo, will probably go gtx3576, modest tune with better spool, and start saving for driveshafts and cvs. 1 Link to comment Share on other sites More sharing options...
Lennox Member 2,586 Member For: 11y 10m 1d Gender: Male Location: Perth Posted 19/04/14 11:17 PM Share Posted 19/04/14 11:17 PM P91 - not for the moment, if I'm honest current power levels exceed my skill level, working on handling mods and getting some experience. .Doesn't stop most people on here!!! Scary how many people just lay down the cash and have 600hp on public roads... 1 Link to comment Share on other sites More sharing options...
MattyP MattyP Cruise Control 6,317 Member For: 12y 7m 23d Gender: Male Location: Central Coast Posted 19/04/14 11:43 PM Share Posted 19/04/14 11:43 PM I have 700hp... Silly me I remember saying 357rwkw was enough Link to comment Share on other sites More sharing options...
Buf-Phoon loitering with intent Lifetime Members 13,318 Member For: 21y 4m 8d Gender: Male Location: Zombie Birdhouse Posted 20/04/14 12:05 AM Share Posted 20/04/14 12:05 AM I find 350 rwkw more than adequate for a daily driver. Still plenty quick and driveable.still chop cars that have more but can't get it to the ground Link to comment Share on other sites More sharing options...
puck_lindsay New Member 21 Member For: 11y 7m 23d Gender: Male Location: Perth, WA Posted 20/04/14 12:47 AM Author Share Posted 20/04/14 12:47 AM Lennox - absolutely. Keep seeing guys in crazy utes lose the tail as they try to nail it out of a corner. Although now that I think about it that may have been intentional..P91 - I know the power bug will rear its head again, but just won't have the funds for turbo+ZF rebuild+driveshafts+CVs+ bigger brakes(stock ones are getting close to their limit+ potentially conrods&pistons. So 480hp is enough for me (for now =P). Still pretty competitive. Not sure how even 600hp would go on the street, let alone 700! Should have reasonable manners down low though. GT42?Buf-phoon (nice handle btw) - that's exactly what I'm worries about now. Got some 245 p zeros on the back and it's just lighting them up without gripping if I give it anything more than half throttle. Any recommendations on better tyres? Link to comment Share on other sites More sharing options...
ratter Member 6,793 Member For: 18y 7m Gender: Male Location: @ my laptop Posted 20/04/14 01:01 AM Share Posted 20/04/14 01:01 AM don't stress too much about that torque number, it is not a representation of engine torque, ask for the derived torque number which will be lower but closer to a correct engine torque Link to comment Share on other sites More sharing options...
Buf-Phoon loitering with intent Lifetime Members 13,318 Member For: 21y 4m 8d Gender: Male Location: Zombie Birdhouse Posted 20/04/14 01:06 AM Share Posted 20/04/14 01:06 AM P Zeroes are not a bad tyre at also tried Yokohama Advans which weren't too bad until about 20ksa good all round tyre IMOHad a set of Maringoni mythos completely delaminate at 15 ks good when new but apparently they went off (aged) in the shedso yeah I ended up running Falken fk452s a good compromise in all conditions V pricesome reading for youhttp://www.productreview.com.au/c/tyres.html 1 Link to comment Share on other sites More sharing options...
puck_lindsay New Member 21 Member For: 11y 7m 23d Gender: Male Location: Perth, WA Posted 20/04/14 03:05 AM Author Share Posted 20/04/14 03:05 AM don't stress too much about that torque number, it is not a representation of engine torque, ask for the derived torque number which will be lower but closer to a correct engine torqueAh, so this would constitute "roller torque"? Difference is variations in calculation due to roller size, etc? Had never heard of that before! Thanks, learnt something. Did you used to (/still have) a turbo EL ONE RAT?P Zeroes are not a bad tyre at also tried Yokohama Advans which weren't too bad until about 20ksa good all round tyre IMOHad a set of Maringoni mythos completely delaminate at 15 ks good when new but apparently they went off (aged) in the shedso yeah I ended up running Falken fk452s a good compromise in all conditions V pricesome reading for youhttp://www.productreview.com.au/c/tyres.htmlCheers mate, thinking about some new wheels, will try some different tread on them when I get there. Love the 19" luxo rims, but they are a bit skinny and wont clear the brake upgrade I'll eventually need. Unless theres a way you can legally and safely make it a 2 piece, keeping the face and widening/putting some rim on? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now