Mago Member 7 Member For: 12y 7m 2d Posted 16/02/14 03:47 AM Share Posted 16/02/14 03:47 AM G'day,I've blown up my 02 xr6 turbo and plan to rebuild it using a spool imports kit with Ross pistons. Would you recommend rebuilding the original turbo engine or buying a low kms NA engine and rebuilding that using the turbo head (or NA) and after market valves, springs, injectors etc in the NA engine. Also which crank should I use if my turbo crank isn't damaged. I'm hoping for 350rwkw on 12psi. Any input or suggestions are welcome!Cheers. Link to comment Share on other sites More sharing options...
sexual harrassment panda I see a red door and I want to paint it black Donating Members 5,919 Member For: 15y 2m 23d Gender: Male Location: Far north queensland Posted 16/02/14 07:52 AM Share Posted 16/02/14 07:52 AM If you blew it up odds are your block is shagged but the crank should be fine. If your head is ok I'd recommend buying a fresh block and giving the head a freshen up and some new valvesprings. Link to comment Share on other sites More sharing options...
Kroozin Menace Donating Members 1,990 Member For: 13y 8m 27d Gender: Male Location: Sydney Posted 16/02/14 08:19 AM Share Posted 16/02/14 08:19 AM (edited) I bought my late model bf motor for 250bux. Same crank. Same cams I think too.. If not could steal the cams outta your dead motor and just fit slightly oversize stainless steel valves.I just through my old bottom end in the bin Edited 16/02/14 08:20 AM by Kroozin 1 Link to comment Share on other sites More sharing options...
sexual harrassment panda I see a red door and I want to paint it black Donating Members 5,919 Member For: 15y 2m 23d Gender: Male Location: Far north queensland Posted 16/02/14 08:34 AM Share Posted 16/02/14 08:34 AM cams =/= Link to comment Share on other sites More sharing options...
Mago Member 7 Member For: 12y 7m 2d Posted 17/02/14 12:44 AM Author Share Posted 17/02/14 12:44 AM Cheers guys, looks like I'll go with a new block and the turbo crank if the original is fine. Also my mate had mentioned that repco are distributors for ACL and their bearings, pistons and rings are a bit cheaper than spool. Anyone have info on ACL? Link to comment Share on other sites More sharing options...
senna_T Forged Member Lifetime Members 15,818 Member For: 17y 11m 10d Gender: Male Location: SW Sydney Posted 17/02/14 01:51 AM Share Posted 17/02/14 01:51 AM ACL is great, I used their bearings in my motor and it did 60,000kms before I sold the car with no issues from the motor Link to comment Share on other sites More sharing options...
Kroozin Menace Donating Members 1,990 Member For: 13y 8m 27d Gender: Male Location: Sydney Posted 17/02/14 04:53 AM Share Posted 17/02/14 04:53 AM Cheers guys, looks like I'll go with a new block and the turbo crank if the original is fine. Also my mate had mentioned that repco are distributors for ACL and their bearings, pistons and rings are a bit cheaper than spool. Anyone have info on ACL?Crank is same same for NA to turboI had the choice of 170,000 turbo crank and 150,000 NA crank.Chose the crank that had done the least amount of work Link to comment Share on other sites More sharing options...
Mago Member 7 Member For: 12y 7m 2d Posted 17/02/14 09:02 AM Author Share Posted 17/02/14 09:02 AM Thanks for the info guys. Finally, any other tips on rebuilding the engine if you have done it before. Cheers Link to comment Share on other sites More sharing options...
Kroozin Menace Donating Members 1,990 Member For: 13y 8m 27d Gender: Male Location: Sydney Posted 17/02/14 10:22 AM Share Posted 17/02/14 10:22 AM (edited) Def. no expert but I believe atomic do a better oil pump setup as ours are known to go to poo, do the spigot bearing while your at it, maybe get your sump checked for being dead flat at joining surface to prevent oil leaks (machinist would probly do that), arp head bolts, you'll probly need to buy a full engine gasket kit which will have all your valve stem seals n that, up to you if you wanna change valves while your at it to the slightly oversized stainless steel type which are avail. (you probly got your money's worth out of the last ones anyway), ask the fella what porting will set you back on the head but be careful who you usemaybe look at doing a timing chain kit too Atomic harmonic balancer (probly not worth worrying about)Get your injectors cleaned Edited 17/02/14 10:22 AM by Kroozin Link to comment Share on other sites More sharing options...
johno Donating Members 773 Member For: 14y 3m 7d Gender: Male Location: Mt Gambier, SA Posted 17/02/14 10:50 AM Share Posted 17/02/14 10:50 AM Was your original engine stock? If so, you will need bigger injectors, modded turbo/wastegate, bigger intercooler, an exhaust system.I wouldnt worry about head porting, or modded cams. Good oil pump, and head bolts yes. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now