sexual harrassment panda I see a red door and I want to paint it black Donating Members 5,919 Member For: 15y 1m 23d Gender: Male Location: Far north queensland Posted 17/06/14 07:25 AM Share Posted 17/06/14 07:25 AM Nearest guru is Ray Hall in cairns, he does balancing (it's not a hard job) amd I'll put $10 on him being cheaper than MTQ anywayHonest guy who knows all there is about turbos 07 4051 6672. MTQ in townsville are hicks 1 Link to comment Share on other sites More sharing options...
MattyP MattyP Cruise Control 6,317 Member For: 12y 7m 14d Gender: Male Location: Central Coast Posted 17/06/14 07:53 AM Share Posted 17/06/14 07:53 AM Dunno about those guys But I got my kinugawa billet wheel balanced at precision turbo wetherill park Sydney Heaps of places can do it I'm a bit confused about the impeller part,Is there something wrong with the turbine? Link to comment Share on other sites More sharing options...
bjc Donating Members 2,823 Member For: 21y 3m 15d Gender: Male Location: Townsville Posted 17/06/14 07:57 AM Share Posted 17/06/14 07:57 AM Cheers mate,I couldn't remember Ray Halls name as it was always on the sponsor board at the Townsville drags and was hoping someone here would do it but NOOOOO....MTQ here just kept on and on about warranty which I kept saying I don't care I just want it balanced and their reply was yeah until it sh*ts itself then we will be in court! Whinging soft *beep* which is a big pity for this town...Will call him tomorrow and hope for the best Link to comment Share on other sites More sharing options...
turbotrana Member 2,586 Member For: 21y 8m 18d Gender: Male Posted 17/06/14 08:06 AM Share Posted 17/06/14 08:06 AM I put a KTS Billet wheel on 6 months ago WITHOUT balancing and it works better than it did with the original wheel.I highly recommend KTS.Just make sure when you put it on that you dont bend the shaft by overtorquing the nut.The turbine and compressor wheels are balanced. The issue does not lie with balance so much, It lies more with RUNOUT of the turbine shaft. Link to comment Share on other sites More sharing options...
bjc Donating Members 2,823 Member For: 21y 3m 15d Gender: Male Location: Townsville Posted 17/06/14 08:13 AM Share Posted 17/06/14 08:13 AM Dunno about those guysBut I got my kinugawa billet wheel balanced at precision turbo wetherill park SydneyHeaps of places can do itI'm a bit confused about the impeller part,Is there something wrong with the turbine?No the turbine is fine it was the impeller/compressor that has small chips and marks in the fins Link to comment Share on other sites More sharing options...
MattyP MattyP Cruise Control 6,317 Member For: 12y 7m 14d Gender: Male Location: Central Coast Posted 17/06/14 08:26 AM Share Posted 17/06/14 08:26 AM Ah ok That should be fine if your changing your compressor wheel Link to comment Share on other sites More sharing options...
sexual harrassment panda I see a red door and I want to paint it black Donating Members 5,919 Member For: 15y 1m 23d Gender: Male Location: Far north queensland Posted 17/06/14 08:59 AM Share Posted 17/06/14 08:59 AM just run it, then post youtube skid vid and watch everyone spazz out at the xr6 with a supercharger Link to comment Share on other sites More sharing options...
bjc Donating Members 2,823 Member For: 21y 3m 15d Gender: Male Location: Townsville Posted 17/06/14 09:11 AM Share Posted 17/06/14 09:11 AM Bit hard in the territory! Although it may do a good on the spot donut in the wet? Link to comment Share on other sites More sharing options...
bjc Donating Members 2,823 Member For: 21y 3m 15d Gender: Male Location: Townsville Posted 17/06/14 09:21 AM Share Posted 17/06/14 09:21 AM I put a KTS Billet wheel on 6 months ago WITHOUT balancing and it works better than it did with the original wheel.I highly recommend KTS.Just make sure when you put it on that you dont bend the shaft by overtorquing the nut.The turbine and compressor wheels are balanced. The issue does not lie with balance so much, It lies more with RUNOUT of the turbine shaft.Got a link turbotrana from where you got your KTS from?When you say runout on the turbine shaft isn't the turbos shaft one single piece all the way through? Does the turbine side get a wobble in it somehow or am I completely off the mark here and it has to do with the amount of play? Haha Link to comment Share on other sites More sharing options...
bjc Donating Members 2,823 Member For: 21y 3m 15d Gender: Male Location: Townsville Posted 17/06/14 09:53 AM Share Posted 17/06/14 09:53 AM Just had a read and understand that if there is runout more than the tolerance on the turbine end then it would mean that the compressor end would wobble more (obviously) which it doesn't as its not scraping the compressor housing or virtually any play that I can see or feel?Best I could do would be to use my father in-laws dial gauge or dont bother?Peoples thoughts on getting it balanced or not? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now