Besty221 Member 18 Member For: 11y 3m 5d Gender: Male Location: Cobar Posted 24/10/13 12:33 AM Share Posted 24/10/13 12:33 AM What I've done so far: -Stage 3 process west front mount incooler -Process west intake plenum -4inch intake -Battery relocation -GT 3582R high flowed nd flapper mod with 64mm compressor wheel -12 psi actuator -Xforce stainless 4inch dump to 3.5 inch exhaust -earls Braided oil feed line nd high flow coolant lines -660cc injectors Looking to have done before tune: -Ace clutch option 5 -process west surge tank with single walbro 460 pump What other mods should be done before the tune to be sorta on the safe side ? How much power ruffly do you reckon I'll make pretty keen to crack 400kw mark .. Any advice would be appreciated 1 Link to comment Share on other sites More sharing options...
gaz097 Bronze Donating Members 1,751 Member For: 13y 4m 10d Posted 24/10/13 01:16 AM Share Posted 24/10/13 01:16 AM U have it covered pretty well and depending how far u want to go on a standard motor. Oil pump gears and maybe a tail shaft in the future would be smart. 400kw and a manual make it very difficult to stay of the limiter Link to comment Share on other sites More sharing options...
gaz097 Bronze Donating Members 1,751 Member For: 13y 4m 10d Posted 24/10/13 01:19 AM Share Posted 24/10/13 01:19 AM Ohh and U should crack 400 pretty easy as well. I went 370 without planum and front wheel very easily Link to comment Share on other sites More sharing options...
BenDoCo I'm getten too old for this s**t Bronze Donating Members 4,509 Member For: 11y 7m 24d Gender: Male Location: A big bridge over a river in South Australia Posted 24/10/13 01:51 AM Share Posted 24/10/13 01:51 AM great to have the power but please make sure you can stop the beast........think about the brakes as well Link to comment Share on other sites More sharing options...
Buf-Phoon loitering with intent Lifetime Members 13,318 Member For: 21y 3m 11d Gender: Male Location: Zombie Birdhouse Posted 24/10/13 02:28 AM Share Posted 24/10/13 02:28 AM what he said Link to comment Share on other sites More sharing options...
Besty221 Member 18 Member For: 11y 3m 5d Gender: Male Location: Cobar Posted 24/10/13 04:31 AM Author Share Posted 24/10/13 04:31 AM U have it covered pretty well and depending how far u want to go on a standard motor. Oil pump gears and maybe a tail shaft in the future would be smart. 400kw and a manual make it very difficult to stay of the limiterYeah well I guess 400kw in a manual is sorta where I wanna hang around ,, aww like ya said I'll be limita bashing everywhere haha So can you elaborate on the oil pump gears, what do they do ? , nd what do u reckon bigger/stronger tail shaft? Link to comment Share on other sites More sharing options...
Besty221 Member 18 Member For: 11y 3m 5d Gender: Male Location: Cobar Posted 24/10/13 04:33 AM Author Share Posted 24/10/13 04:33 AM great to have the power but please make sure you can stop the beast........think about the brakes as wellHaha yeah mate I bought dimpled rotors nd some sticky brake pads nd wacked them on but yeah I'll eventually get brembos I guess - when I can afford them :/ do use know of any other decent set ups that are on the cheap side but are just as good ? Link to comment Share on other sites More sharing options...
Besty221 Member 18 Member For: 11y 3m 5d Gender: Male Location: Cobar Posted 24/10/13 04:33 AM Author Share Posted 24/10/13 04:33 AM What's your ideas on value springs ? Needed ASAP or wha ?? Link to comment Share on other sites More sharing options...
ms700 Moderating Team 10,170 Member For: 21y 9m 30d Gender: Male Location: Sydney Posted 24/10/13 04:35 AM Share Posted 24/10/13 04:35 AM Cheap brakes?!?!note to self, dont plan any trips to cobar anytime soon..... 2 Link to comment Share on other sites More sharing options...
gaz097 Bronze Donating Members 1,751 Member For: 13y 4m 10d Posted 24/10/13 04:54 AM Share Posted 24/10/13 04:54 AM Atomic oil pump gears as hitting the limiter causes a jolt which can shear them. Tail shaft in my opinion is wait for it to break lol and I would do valve springs for sure. 400 is a lot of strain on something that is known to fail Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now