Bizkets is Drunk? Too heavy needs boost Member 5,929 Member For: 11y 4m 18d Gender: Male Location: Adelaide Posted 09/10/13 08:35 AM Share Posted 09/10/13 08:35 AM ss inductions holder I'm getting one of these. Are they any good. Easy to put in and the 52 mil gauges fit fine? Link to comment Share on other sites More sharing options...
Lennox Member 2,586 Member For: 11y 9m 28d Gender: Male Location: Perth Posted 09/10/13 08:38 AM Share Posted 09/10/13 08:38 AM Yes 52mm fit fine, weird how they say on their website that they may not fit? Link to comment Share on other sites More sharing options...
AzMahoony Hench, but no longer shredded or tanned. Member 3,343 Member For: 17y 8m 26d Gender: Male Location: Canning Vale, W.A Posted 09/10/13 11:27 AM Share Posted 09/10/13 11:27 AM I'd only get a gauge holder like the above. These cars should be kept somewhat classy, they're not japanese drift cars where you have 20 gauges going down the drivers side pillar and all over dash. 1 Link to comment Share on other sites More sharing options...
brycieboy Member 6 Member For: 11y 11m 5d Gender: Male Location: carrum downs Posted 09/10/13 09:52 PM Share Posted 09/10/13 09:52 PM (edited) I'm getting one of these. Are they any good. Easy to put in and the 52 mil gauges fit fine?kinda.... the aeroforce gauges needed a few wraps with some tape to make them fit snug. the autometer gauge needed the holder modded to fit. (though its a mechanical boost gauge. mounting bolts had to be cut down, hooles for them had to be made bigger in the cup, the base plate had to be modded as the fittings hit.also fairly easy to fit. I was a little concerned when the instructions said to use a screwdriver or butter knife though.... just dont loose the yellow clips into the dash. Edited 09/10/13 09:53 PM by brycieboy Link to comment Share on other sites More sharing options...
Lennox Member 2,586 Member For: 11y 9m 28d Gender: Male Location: Perth Posted 10/10/13 01:51 AM Share Posted 10/10/13 01:51 AM I have autometer gauges and all I had to do was cut down the brass studs so the backs of the cups would go back on Link to comment Share on other sites More sharing options...
CHLAXN Donating Members 932 Member For: 16y 7m 2d Gender: Male Location: north QLD Posted 10/10/13 02:19 AM Share Posted 10/10/13 02:19 AM kinda.... the aeroforce gauges needed a few wraps with some tape to make them fit snug. the autometer gauge needed the holder modded to fit. (though its a mechanical boost gauge. mounting bolts had to be cut down, hooles for them had to be made bigger in the cup, the base plate had to be modded as the fittings hit.also fairly easy to fit. I was a little concerned when the instructions said to use a screwdriver or butter knife though.... just dont loose the yellow clips into the dash.If you use electric gauges you don't have to modify any thing on the gauge holder. Just have to trim the brass mounting bolts on the gauges shorter. Here is a pic of mine Link to comment Share on other sites More sharing options...
edawg91 Member 26 Member For: 11y 2m 20d Gender: Male Location: Gatton, Lockyer Valley Posted 11/10/13 12:42 PM Author Share Posted 11/10/13 12:42 PM I must admit, I didnt like the ss inductions, but after seeing the photos, they look really good. Link to comment Share on other sites More sharing options...
coolfgxr6t Member 30 Member For: 11y 3m 23d Posted 11/10/13 09:31 PM Share Posted 11/10/13 09:31 PM Is it hard to install the ss inductions pod? is it a diy thing? also are the gauges hard to connect up or is it best to take them to auto sparky? Sent from my GT-I9300T using Tapatalk 2 Link to comment Share on other sites More sharing options...
RowdyBurns Donating Members 641 Member For: 16y 9m 16d Gender: Male Location: Brisbane Posted 12/10/13 12:07 AM Share Posted 12/10/13 12:07 AM The SS pod just clips in to the factory position. It's the wiring and installing senders that will test you if you don't know what you are doing. It's not the most difficult job to do and there are a few tutorials on here, but save yourself the headache if you aren't 'mechanically minded'. Link to comment Share on other sites More sharing options...
useless Member 259 Member For: 20y 6m 22d Gender: Male Posted 02/01/17 02:32 AM Share Posted 02/01/17 02:32 AM On Wednesday, October 09, 2013 at 7:38 PM, Lennox said: Yes 52mm fit fine, weird how they say on their website that they may not fit? No they dont.You can't fit a mechanical autometer boost gauge to them without a grinder to cut a big hole in the pod then hack the top of the holder Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now