Chaos310 Donating Members 228 Member For: 12y 3m 25d Gender: Male Posted 10/04/13 11:13 AM Author Share Posted 10/04/13 11:13 AM Surge tank has turned up... its a thing of beauty. Was going to do a mount bracket in SolidWorks to have CNC machined, but I think I'll just do a basic plate mount and go from there. I'll be ordering all the fuel lines and fittings before the week is out and hopefully plumbing it all up in the next fortnight... hopefully.. Link to comment Share on other sites More sharing options...
f6mark Member 2,908 Member For: 13y 10m 12d Gender: Male Posted 10/04/13 06:52 PM Share Posted 10/04/13 06:52 PM so XFT it is then mate.?? good stuff.. Link to comment Share on other sites More sharing options...
Chaos310 Donating Members 228 Member For: 12y 3m 25d Gender: Male Posted 15/04/13 11:17 AM Author Share Posted 15/04/13 11:17 AM (edited) OK,so attached pics show my new surge tank. It houses a Walbro 400 like I mentioned above, -6an fittings and holds around 1.5L from what I can find on the web page.Pretty neat bit of gear I think.Reasonably priced too and will fit on the rail in my FG like the other units on the market.green fitting is pump out. Edited 15/04/13 11:19 AM by Chaos310 2 Link to comment Share on other sites More sharing options...
Chaos310 Donating Members 228 Member For: 12y 3m 25d Gender: Male Posted 17/05/13 10:20 AM Author Share Posted 17/05/13 10:20 AM OK, so the turbo is coming off the ute tomorrow and heading off for work IWG open up, 12lb actuator and a little here and there..The injectors have been cleaned and tested and all the other parts have been brought together to be fitted up ready to roll.Went and spoke to Rob at Monsta Torque again, met Darren (formerly BlackMac workshop) both are keen to see the ute.The Xcal3 has been loaded with a set of trim codes so I can get the car to them after fitting the new injectors.I'll take a bunch of pics for before and afters.New tyres surely in the near future...cheers 1 Link to comment Share on other sites More sharing options...
Chaos310 Donating Members 228 Member For: 12y 3m 25d Gender: Male Posted 19/05/13 03:43 AM Author Share Posted 19/05/13 03:43 AM with the assistance of a fellow forum member and his awesome workshop works have started...The turbo is out (pics soon)injectors are in, new exhaust is in place, plugs are gapped, thermostat has been fitted <--- the housing had some low spots on it in the casting so it was draw filed back flush on both sides for better contact.the exhaust bolts weren't too bad to get off, I was expecting much worse, although at 34000km, maybe its not long enough to weld them in place. the new exhaust is a thing of beauty... all shiny and big, went in with out a hitch which I was most impressed aboutsome pics of the previous days efforts.New intake bend too... a touch bigger than the stock item. 1 Link to comment Share on other sites More sharing options...
f6mark Member 2,908 Member For: 13y 10m 12d Gender: Male Posted 19/05/13 04:36 AM Share Posted 19/05/13 04:36 AM looks good mate. r u going to run the PW turbo side relo kit mate.?? Link to comment Share on other sites More sharing options...
Chaos310 Donating Members 228 Member For: 12y 3m 25d Gender: Male Posted 19/05/13 05:45 AM Author Share Posted 19/05/13 05:45 AM I was thinking about it however at this point in time the budget does not allow it. MAYBE... later on.. although if I pop over the 500-520hp mark I'll probably just leave it alone. I know guys are making 530+ on the stock intake, with a modded lower half airbox, so that'll be me for a while.PLUS, I'd prefer to leave the bay looking stock for those points in time where certain "mechanics" in cars with lights on the roof tell you about everything you've done wrong... 1 Link to comment Share on other sites More sharing options...
Chaos310 Donating Members 228 Member For: 12y 3m 25d Gender: Male Posted 20/05/13 12:00 PM Author Share Posted 20/05/13 12:00 PM OK, some pics of the turbo before the work..button is 33mm in dia... this will change to 38mmbutton seat area is 3mm wide... this will become 1mmbore dia is 27mm (not incl the top flat portion) this will become 36mmblue paint just to highlight areas before work.The internal shot just there to show factory casting flow path.cheers 2 Link to comment Share on other sites More sharing options...
julesk_1972 Member 267 Member For: 12y 5m 1d Gender: Male Location: Perth Posted 21/05/13 11:31 AM Share Posted 21/05/13 11:31 AM Huge exhaust!!!Look forward to seeing the results, will be a handful. 2 Link to comment Share on other sites More sharing options...
Chaos310 Donating Members 228 Member For: 12y 3m 25d Gender: Male Posted 22/05/13 11:58 AM Author Share Posted 22/05/13 11:58 AM Turbo is back! Had it looked at for an opinion on the job done and while the job has been done very well, generally the IWG's are touched up by the tuner in a few places. Each tuner is different and they like different port finishes, so mine will be touched up ever so lightly before going back on the ute.I'm a pretty picky kind of bloke when it comes to my things which is why I like to have as much input as possible and where I can and feel confident, I like to do the work myself. There are Pro's and Con's to this. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now