131FPV Member 87 Member For: 12y 6m 27d Gender: Male Location: Brisbane Posted 14/01/13 10:47 AM Author Share Posted 14/01/13 10:47 AM Sounds like somethings up with the pump/gears/ set up install ....... Or uve got a blockage ina oil gallery/'sOnly thing I can think of the builder said he had to do some milling to get the atomic street girdle to fit. I was pretty sure you only had to mod the race plate. Does anyone know if the girdle sits very close to the oil pickup ? Link to comment Share on other sites More sharing options...
131FPV Member 87 Member For: 12y 6m 27d Gender: Male Location: Brisbane Posted 14/01/13 10:51 AM Author Share Posted 14/01/13 10:51 AM The other thing that keeps popping up when talking between the builder and the dyno shop is the fact that the rods have 30thou of side clearence. The standard rods have 10thou I'm just got no idea and its driving me bonkers Link to comment Share on other sites More sharing options...
JETURBO ...JD TUNING ADELAIDE... Gold Donating Members 23,708 Member For: 16y 5m 10d Gender: Male Location: Adelaide Posted 14/01/13 10:59 AM Share Posted 14/01/13 10:59 AM Urr that's weird Spool rods are balanced already, did the builder balance and blueprint the assembly ? that's the only reason I can think why the extra clearance is there If the supplyed parts are true and correct then its in the builders hands Not passing any blame across but a builder will weigh and measure even new supplied parts so he knows that hardwear is fine to begin with Link to comment Share on other sites More sharing options...
131FPV Member 87 Member For: 12y 6m 27d Gender: Male Location: Brisbane Posted 14/01/13 11:13 AM Author Share Posted 14/01/13 11:13 AM Urr that's weirdSpool rods are balanced already, did the builder balance and blueprint the assembly ? that's the only reason I can think why the extra clearance is thereIf the supplyed parts are true and correct then its in the builders handsNot passing any blame across but a builder will weigh and measure even new supplied parts so he knows that hardwear is fine to begin withYeah he did balance the bottom end. Link to comment Share on other sites More sharing options...
JETURBO ...JD TUNING ADELAIDE... Gold Donating Members 23,708 Member For: 16y 5m 10d Gender: Male Location: Adelaide Posted 14/01/13 11:17 AM Share Posted 14/01/13 11:17 AM Well dude it looks like it needs to be pulled down and start with a good wash clean and re measure/assemble Somethings going to rear its ugly head Link to comment Share on other sites More sharing options...
welshy_89 Member 131 Member For: 13y 3m 16d Posted 14/01/13 12:20 PM Share Posted 14/01/13 12:20 PM I thought spool rods are made that way to try and keep the engine quieter and I think ull find even atomic rods are similarly offset... Cld be wrong though... Hope u get to the bottom of it either way... Sent from my HTC Velocity 4G using Tapatalk 2 Link to comment Share on other sites More sharing options...
131FPV Member 87 Member For: 12y 6m 27d Gender: Male Location: Brisbane Posted 15/01/13 07:44 AM Author Share Posted 15/01/13 07:44 AM So got a question for everyone. Does anyone know if the factory VCT cam gears are meant to bleed oil ? Th exhaust one is leaking more than the intake one. I asked brad from atomic and he's pretty sure that they aren't meant to. Link to comment Share on other sites More sharing options...
relentless xr6 Member 363 Member For: 13y 11m 6d Gender: Male Location: Sydney Posted 12/02/13 10:16 AM Share Posted 12/02/13 10:16 AM Did some calcs on the flow figures posted.average from .200 valve lift to .500 valve lift intake before mods 223.49 cfmaverage from .200 valve lift to .500 valve lift intake after mods 229.83 cfmaverage improvement total 6.34 cfm intake.average from .200 valve lift to .500 valve lift exhaust before mods 162.26 cfmaverage from .200 valve lift to .500 valve lift exhaust after mods 171.25 cfmaverage improvement total 8.99 cfm exhaust. 1 Link to comment Share on other sites More sharing options...
nitro xr6 turbo Banned 185 Member For: 12y 11m 27d Gender: Male Location: perth wa Posted 12/02/13 01:22 PM Share Posted 12/02/13 01:22 PM any updates on the build? Link to comment Share on other sites More sharing options...
131FPV Member 87 Member For: 12y 6m 27d Gender: Male Location: Brisbane Posted 13/02/13 11:39 AM Author Share Posted 13/02/13 11:39 AM any updates on the build?Well got a call on Monday from the builder and he said he change the VCT gears and re pressurised the system and the gears did not leak as much as the original set, so fingers crossed that was the problem. The builder also said that because the gears aren't able to be checked normally that he is not going to pay for the 2 times the motor came out.Wait and see that this was the problem. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now