Bizkets is Drunk? Too heavy needs boost Member 5,929 Member For: 11y 10m 29d Gender: Male Location: Adelaide Posted 04/12/13 03:57 AM Share Posted 04/12/13 03:57 AM People that are on 3 times the money I'm on at work and they are mentally retarded. Link to comment https://www.fordxr6turbo.com/forum/topic/81368-the-whats-piing-you-off-thread/page/827/#findComment-1443831 Share on other sites More sharing options...
Never had any say Panda I <3 Floods Silver Donating Members 11,198 Member For: 13y 11m 4d Gender: Male Location: South West QLD Posted 04/12/13 05:02 AM Share Posted 04/12/13 05:02 AM Dddduuuuuuuuhhhhhhhh Drool Link to comment https://www.fordxr6turbo.com/forum/topic/81368-the-whats-piing-you-off-thread/page/827/#findComment-1443862 Share on other sites More sharing options...
discostig Manual mode ________________________ All day, erryday Donating Members 13,798 Member For: 17y 7m 10d Gender: Male Location: Probably above atmospheric pressure Posted 04/12/13 05:53 PM Share Posted 04/12/13 05:53 PM These farking bolts. SO hard to do up in the limited space, I need half moon spanners. Link to comment https://www.fordxr6turbo.com/forum/topic/81368-the-whats-piing-you-off-thread/page/827/#findComment-1443961 Share on other sites More sharing options...
willo88 Member 700 Member For: 13y 5m 10d Gender: Male Location: Newcastle Posted 04/12/13 07:18 PM Share Posted 04/12/13 07:18 PM Truetrac being installed today annnnnnnnnd it's pissing down rain... Link to comment https://www.fordxr6turbo.com/forum/topic/81368-the-whats-piing-you-off-thread/page/827/#findComment-1443968 Share on other sites More sharing options...
hawlass Silver Donating Members 1,161 Member For: 17y 7m 26d Gender: Male Location: left right out Posted 05/12/13 07:50 AM Share Posted 05/12/13 07:50 AM (edited) ^^ SteveR, what you need is a ratcheting open ended spanner, there are quality brands available along with the cheaper ones. Buy a cheap one in the right size and cut to length to fit . I'm asking santa for a set this year. Edited 05/12/13 07:50 AM by hawlass 1 Link to comment https://www.fordxr6turbo.com/forum/topic/81368-the-whats-piing-you-off-thread/page/827/#findComment-1444083 Share on other sites More sharing options...
Dagabond Bored Member Administrator 35,722 Member For: 22y 7m 21d Gender: Male Location: Dé·jà vu Posted 05/12/13 09:09 AM Share Posted 05/12/13 09:09 AM I'd like to see it tighten a heated dried out housing bolt and not just a small flare nut and one on a spanking clean thread.....I can imagine the next thread somebody posts already...."How do you remove nuts with rounded corners?" Link to comment https://www.fordxr6turbo.com/forum/topic/81368-the-whats-piing-you-off-thread/page/827/#findComment-1444103 Share on other sites More sharing options...
ratter Member 6,793 Member For: 19y 1m 8d Gender: Male Location: @ my laptop Posted 05/12/13 09:18 AM Share Posted 05/12/13 09:18 AM -SteveR- your turbo housing Is most likely cracked 1 Link to comment https://www.fordxr6turbo.com/forum/topic/81368-the-whats-piing-you-off-thread/page/827/#findComment-1444105 Share on other sites More sharing options...
k31th less WHY; more WOT Site Developer 29,586 Member For: 17y 2m 25d Gender: Male Location: Melbourne Posted 05/12/13 09:23 AM Share Posted 05/12/13 09:23 AM Why are you so doubtful, Dags? It's a simple one-way mechanism, it loosens the teeth on one side going one direction and tightens going the other direction. The teeth are as good, if not better, than any other type of ratchet spanner, so why would it be rounding bolts?Even if you are right, rounded bolts can be dealth with, too. Link to comment https://www.fordxr6turbo.com/forum/topic/81368-the-whats-piing-you-off-thread/page/827/#findComment-1444107 Share on other sites More sharing options...
Dagabond Bored Member Administrator 35,722 Member For: 22y 7m 21d Gender: Male Location: Dé·jà vu Posted 05/12/13 09:41 AM Share Posted 05/12/13 09:41 AM As I said I'd like to see it done before handing out the readies.The torsion involved is way above anything they showed in the video and looking at the ratcheting tooth it looks like it would slip very easily to me. Happy to be proved wrong.In saying that you could only use it to advance the thread and use a normal spanner for the final tightening. Link to comment https://www.fordxr6turbo.com/forum/topic/81368-the-whats-piing-you-off-thread/page/827/#findComment-1444111 Share on other sites More sharing options...
k31th less WHY; more WOT Site Developer 29,586 Member For: 17y 2m 25d Gender: Male Location: Melbourne Posted 05/12/13 09:43 AM Share Posted 05/12/13 09:43 AM I'm thinking I'll get a set... now whether to get the 3x double-ended ratcheting jobbies or the set of 10 with spanner on one end and ratcheting spanner on the other end... Link to comment https://www.fordxr6turbo.com/forum/topic/81368-the-whats-piing-you-off-thread/page/827/#findComment-1444113 Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now