WhiteXR Member 117 Member For: 14y 1m 13d Gender: Male Location: sydney Posted 17/05/11 05:23 AM Share Posted 17/05/11 05:23 AM I just sent aeroforce an email asking if their gauges are metric, I heard somewhere they are imperial and dont work the same (for instance it shows gallon/per 100 mile), XTREME Gauges supply the right metric one but id rather save my hundred dollars!Il get back to yous!http://www.aeroforcetech.com/products_order_ford.htmlWe use the CNF model gauge. Link to comment Share on other sites More sharing options...
discostig Manual mode ________________________ All day, erryday Donating Members 13,798 Member For: 17y Gender: Male Location: Probably above atmospheric pressure Posted 17/05/11 05:23 AM Share Posted 17/05/11 05:23 AM Oh now I need 5 gauges! Would like trans temp... Link to comment Share on other sites More sharing options...
Bigkeels Throbbing Member Donating Members 594 Member For: 15y 9m 20d Gender: Male Location: Victoria Posted 17/05/11 06:46 AM Share Posted 17/05/11 06:46 AM On mine you can choose to display it in metric or imperial, depends what parameters you select it to display. Link to comment Share on other sites More sharing options...
xr6turboman Donating Members 588 Member For: 16y 7m 12d Gender: Male Location: New Zealand, Palmerston North Posted 17/05/11 07:42 AM Share Posted 17/05/11 07:42 AM The bung has an M18x1.5mm thread to suit the 02 sensor. They cost about $4.... You just need to get a exhaust shop to weld in it (in the dump before the cat at least 300mm from the turbine outlet is the best combo for accuracy and sensor life. you can go closer to the turbin but the sensor wont last as long) Its very important that the sensor is mounted at leat 15 deg above horizontal so any condensation the builds up in the exhaust drain off and does cause the sensor heater element to crack/fail Link to comment Share on other sites More sharing options...
SuckSqueezeBangBlow ʎǝʞuoɯ ɹoıuǝs Donating Members 1,808 Member For: 15y 11m 9d Gender: Male Posted 17/05/11 11:02 AM Share Posted 17/05/11 11:02 AM (edited) if you buy an innovate LC-1 you can just put the wideband sensor in the factory 02 sensor bung, and connect one of the outputs as a narrowband signal to your PCM, and the second output as a wideband signal to your gauge (you program the settings via laptop)I just got the second bung welded in though.whats so dodgy about innovate is that they used to advertise the OT-2 as being able to monitor trans temp BUT IT CAN'T. I emailed them abuse again and again and now they have changed their web page so it doesn't mention it. Edited 17/05/11 11:05 AM by JC807 Link to comment Share on other sites More sharing options...
WhiteXR Member 117 Member For: 14y 1m 13d Gender: Male Location: sydney Posted 21/05/11 05:09 AM Share Posted 21/05/11 05:09 AM I just wanted to know as Im getting an aeroforce gauge. I wanted to hook the oil temp sensor to it to read it on my ba and was wondering do I get the 1/8 or the 3/8 sensor.Thanks! Link to comment Share on other sites More sharing options...
SuckSqueezeBangBlow ʎǝʞuoɯ ɹoıuǝs Donating Members 1,808 Member For: 15y 11m 9d Gender: Male Posted 21/05/11 06:14 AM Share Posted 21/05/11 06:14 AM depends where you are going put the sender. I used a sandwich plate underneath the oil filter, worked for me and didn't leak. another option is put in a brass section near the factory oil pressure sender. 1/8 I think the sandwich plate is. Link to comment Share on other sites More sharing options...
bjc Donating Members 2,823 Member For: 21y 2m 21d Gender: Male Location: Townsville Posted 21/05/11 07:53 AM Share Posted 21/05/11 07:53 AM You cant read oil temps for the BA series gearbox or engine so just buy a oil temp sensor that has 5v ability to plug straight into the guages aux on the back.I'm still working mine out as I was having a problem with the annunciator (light that flash for anything you want). Link to comment Share on other sites More sharing options...
ratter Member 6,793 Member For: 18y 5m 29d Gender: Male Location: @ my laptop Posted 21/05/11 12:12 PM Share Posted 21/05/11 12:12 PM pretty sure BA will show engine oil temp through the obd2 if that's what you meant, I know the FG's do, looked at it the other day Link to comment Share on other sites More sharing options...
WhiteXR Member 117 Member For: 14y 1m 13d Gender: Male Location: sydney Posted 21/05/11 02:21 PM Share Posted 21/05/11 02:21 PM Now this gets confusing haha.. Some say it show btr trans temp through the aeroforce. some say it doesnt. I want to definately know my oil temp aswell as that's quite important before giving big hits Who ever has a BA with this gauge, can you please give input to what features you see from simply plugging the gauge to the OBD2 port.cheers! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now