Paulie2256 Donating Members 7,441 Member For: 16y 7d Gender: Male Location: SE Melbourne Posted 18/09/12 01:05 AM Share Posted 18/09/12 01:05 AM Battery to boot relo, just arrived from forum member in SA.Nekminutnew thread titled "My car wont start, speedo not working" Link to comment Share on other sites More sharing options...
Ciaran Thooperrrrrrr Donating Members 2,768 Member For: 13y 4m 27d Gender: Male Location: NOR, Western Australia Posted 18/09/12 01:16 AM Share Posted 18/09/12 01:16 AM ^ Buys Boot kitFits in Engine bay.....Was $50 lol, cant complain? Link to comment Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,323 Member For: 19y 2m 6d Gender: Male Location: Perth Posted 18/09/12 01:34 AM Author Share Posted 18/09/12 01:34 AM 36 row B&M cooler and Aeroflow fittings,don't know yet where she's going to fit lol.Seems to fit the chair pretty well? 1 Link to comment Share on other sites More sharing options...
JETURBO ...JD TUNING ADELAIDE... Gold Donating Members 23,708 Member For: 16y 5m 29d Gender: Male Location: Adelaide Posted 18/09/12 01:42 AM Share Posted 18/09/12 01:42 AM Front mount FTW gilly workx for both my donkeysTwas a full carpet box hey kerry looked good in his foon Link to comment Share on other sites More sharing options...
Ciaran Thooperrrrrrr Donating Members 2,768 Member For: 13y 4m 27d Gender: Male Location: NOR, Western Australia Posted 18/09/12 01:49 AM Share Posted 18/09/12 01:49 AM Yeah where did he mount it? left or right of boot?I'll need to get a new battery if I relocate it to the boot Link to comment Share on other sites More sharing options...
JETURBO ...JD TUNING ADELAIDE... Gold Donating Members 23,708 Member For: 16y 5m 29d Gender: Male Location: Adelaide Posted 18/09/12 01:52 AM Share Posted 18/09/12 01:52 AM More to the passenger side close to the back seat up on the hump Link to comment Share on other sites More sharing options...
Ciaran Thooperrrrrrr Donating Members 2,768 Member For: 13y 4m 27d Gender: Male Location: NOR, Western Australia Posted 18/09/12 01:53 AM Share Posted 18/09/12 01:53 AM Ah yep has a bit of a groove in the box, I assume that's where it slotted in against the roof of the boot Link to comment Share on other sites More sharing options...
GTEXXED Banned Banned 910 Member For: 12y 4m 9d Gender: Male Posted 18/09/12 02:06 AM Share Posted 18/09/12 02:06 AM (edited) Here's a idea blokeBack left corner and bolted the tray to the floor followed by battery to the tray.She now has a much stronger hold down that doesn't flex one bit.I just used the factory amp location for an earth and ran another earth from battery to engine block and then to body again creating an earth circuit so to speak,didn't loose a volt anywhere.I used an old mouse pad under the battery to keep it extra still,battery on plastic coated tray doesn't work well imo,I have the exact tray on mine.I was going to mount under boot roof but couldn't get to the bolt from underneath to hold tray down nice and firm,no way was I going to use some tek screws....maybe I missed a way to get to the other end of bolt? Edited 18/09/12 02:08 AM by GTEXXED Link to comment Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,323 Member For: 19y 2m 6d Gender: Male Location: Perth Posted 18/09/12 02:22 AM Author Share Posted 18/09/12 02:22 AM Pic's of cable exit holes and routing under the car? Link to comment Share on other sites More sharing options...
GTEXXED Banned Banned 910 Member For: 12y 4m 9d Gender: Male Posted 18/09/12 02:31 AM Share Posted 18/09/12 02:31 AM earth runs down left hand side of car inside cabin(like an amp cable)and the power is run down the drivers side of the car.All cables are protected by convaluted tubing and fully wrapped in electrical tape twice(like factory looms).Both wires come out of the factory large grommet hole in drivers foot well,this was carefully trimmed and still sits in place as per factory.I also run an isolator switch in the engine bay.I'm not a fan of running power cables under the vehicle body so this was the best way,I have had the interior out on the weekend and all wires are still sitting where they were and haven't come into contact/rubbing with anything. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now