Panda Eyes flame magnet Gold Donating Members 5,674 Member For: 16y 6m 1d Gender: Male Location: adelaide hills- 'race air' central Posted 01/09/12 10:40 AM Author Share Posted 01/09/12 10:40 AM nice. I havent played with the 660 yet, but am realy looking forward to it with the 3 way front stage. from everything I have researched, it should do the trick nicely... Link to comment Share on other sites More sharing options...
jrjoz Member 23 Member For: 12y 4m 14d Gender: Male Location: Victoria Posted 02/09/12 02:00 PM Share Posted 02/09/12 02:00 PM How are you doing a 3 way front stage off the 660?You only have crossovers and outputs to go 2 way right?I spent some more time on my tune today as well, had a spectrum analyser running all the way through set up.Got it much flatter but still have a dip at 400hz that the 660 doesn't give me the ability to correct.Also made 10 reference measurements all around the drivers head position which gave much better results than the standard 4 that it asks for.Here is my little tune set up... 1 Link to comment Share on other sites More sharing options...
spook Donating Members 180 Member For: 16y 7m 13d Gender: Male Posted 03/09/12 02:47 AM Share Posted 03/09/12 02:47 AM (edited) The rear or fronts only are fine as either receive full range when sub amp disconnected. The ICC has no separate tweeter output in any case.Hey jrjoz, did you tune with a laptop and I presume the Imprint ap? and if so what final "profile" did youy select? Edited 03/09/12 02:54 AM by spook Link to comment Share on other sites More sharing options...
jrjoz Member 23 Member For: 12y 4m 14d Gender: Male Location: Victoria Posted 04/09/12 10:06 AM Share Posted 04/09/12 10:06 AM When I started work I tested both front and rear outputs against each other and didn't notice any difference.Yeah I did the basic set up off the unit then re did everything off the laptop.Final profile I went for was the 3rd one I think, pretty much pushed the bass all the way up with a high end roll off.I also used the second option in the click boxes which was another high roll off filter.Even at this point it was still pretty lumpy, I then ran pink noise off my ipod and also a Test CD and used the parametric eq to solves some issues.Would be sooooo much simpler if there was a 31band graphic in there somewhere. 3 band parametric is a joke and the laptop control is still super limited.Cheers, J Link to comment Share on other sites More sharing options...
Panda Eyes flame magnet Gold Donating Members 5,674 Member For: 16y 6m 1d Gender: Male Location: adelaide hills- 'race air' central Posted 04/09/12 11:34 AM Author Share Posted 04/09/12 11:34 AM im still in the baby stage with the imprint. 6 channels though right? if nothing else I can pass through some rcas on the 4 channel amp and run the same signal to the 2 channel. level will be the same from the 660, but I can adjust the amp level to suit volume requirements... Link to comment Share on other sites More sharing options...
jrjoz Member 23 Member For: 12y 4m 14d Gender: Male Location: Victoria Posted 05/09/12 11:20 AM Share Posted 05/09/12 11:20 AM It's more about your cross over points.In a 2 way you would set 1 cross over around 2.5khzFor 3 way you need 2 points around 900hz and 3.15khzThe imprint has 6 outs beingL/R TweeterL/R mid L/R rearI dont think you get a cross over on the L/R rearI could be wrong though.J Link to comment Share on other sites More sharing options...
Mr_xr6_Turbo1 Member 57 Member For: 14y 1m 4d Posted 10/09/12 07:50 AM Share Posted 10/09/12 07:50 AM I am about the start my installing Using a H800 and some very top end gear I can keep you guys updated if you like Link to comment Share on other sites More sharing options...
spook Donating Members 180 Member For: 16y 7m 13d Gender: Male Posted 10/09/12 10:33 AM Share Posted 10/09/12 10:33 AM Always good to see different installs Link to comment Share on other sites More sharing options...
Panda Eyes flame magnet Gold Donating Members 5,674 Member For: 16y 6m 1d Gender: Male Location: adelaide hills- 'race air' central Posted 10/09/12 11:04 PM Author Share Posted 10/09/12 11:04 PM It's more about your cross over points.In a 2 way you would set 1 cross over around 2.5khzFor 3 way you need 2 points around 900hz and 3.15khzThe imprint has 6 outs beingL/R TweeterL/R midL/R rearI dont think you get a cross over on the L/R rearI could be wrong though.Jim not having any rears, so will all go to the front.im still moving along, but flat out at work so not as much as id like to. when I get chance ill update piccies. Link to comment Share on other sites More sharing options...
Panda Eyes flame magnet Gold Donating Members 5,674 Member For: 16y 6m 1d Gender: Male Location: adelaide hills- 'race air' central Posted 14/10/12 11:15 AM Author Share Posted 14/10/12 11:15 AM so some updates- I havent posted for a while, but have been steadily working on the build...started on the door trims:the speaker grills are plastic riveted to the door card, so I got my grinder out and nipped them offtime for tape and fibreglass. I sprayed the tape with cooking spray so the fibreglass will release.also remember to clean the areas to be taped thoroughly with prepsol or wax and grease remover, to get rid of old armour all etc. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now