bossmang FREAKY Donating Members 12,433 Member For: 15y 1d Gender: Male Location: Melbourne Posted 22/11/21 09:14 AM Share Posted 22/11/21 09:14 AM (edited) yer I moved to a small country town so even lesser need for 500 kw Edited 22/11/21 09:15 AM by bossmang Link to comment Share on other sites More sharing options...
Puffwagon Puff Gold Donating Members 15,988 Member For: 9y 10m 26d Gender: Male Location: South Australia Posted 22/11/21 09:51 AM Share Posted 22/11/21 09:51 AM Speaking of cars...IMS used 68psi to make 1159wkw. Farken gotta up my game it seems... 1 Link to comment Share on other sites More sharing options...
VitaminG New Member 24 Member For: 5y 7m 18d Gender: Male Location: Queensland Posted 19/01/22 01:38 PM Share Posted 19/01/22 01:38 PM popped some Superpro control blades in the FG this afternoon. I swapped in some Kings SSLs a couple of weeks ago and suddenly it developed a real clunk in the back end. Assumed that I'd screwed something up since the noise started right around that time. Turns out the OEM blades were flogged. So now, I'm low, smooth and it's not as squirrely in rear when putting the power down. So it's like I've added HP too. Link to comment Share on other sites More sharing options...
k31th less WHY; more WOT Site Developer 29,060 Member For: 16y 8m 16d Gender: Male Location: Melbourne Posted 19/01/22 01:49 PM Share Posted 19/01/22 01:49 PM Link to comment Share on other sites More sharing options...
biddie_fiddler [IMPULSIV3] Donating Members 1,374 Member For: 5y 8m 27d Gender: Male Location: Perth, WA Posted 20/01/22 12:22 AM Share Posted 20/01/22 12:22 AM 10 hours ago, VitaminG said: popped some Superpro control blades in the FG this afternoon. I swapped in some Kings SSLs a couple of weeks ago and suddenly it developed a real clunk in the back end. Assumed that I'd screwed something up since the noise started right around that time. Turns out the OEM blades were flogged. So now, I'm low, smooth and it's not as squirrely in rear when putting the power down. So it's like I've added HP too. I did these a while ago on my rig too, could definitely notice a before and after with them! They should last a whole lot longer than the stock ones too, so that's a plus! 1 Link to comment Share on other sites More sharing options...
VitaminG New Member 24 Member For: 5y 7m 18d Gender: Male Location: Queensland Posted 20/01/22 12:52 AM Share Posted 20/01/22 12:52 AM 2 Link to comment Share on other sites More sharing options...
k31th less WHY; more WOT Site Developer 29,060 Member For: 16y 8m 16d Gender: Male Location: Melbourne Posted 20/01/22 12:57 AM Share Posted 20/01/22 12:57 AM Looks great 1 Link to comment Share on other sites More sharing options...
canedkydd Member 56 Member For: 4y 7m 8d Gender: Male Location: Wellington New Zealand Posted 20/01/22 01:00 AM Share Posted 20/01/22 01:00 AM umm what did you do to it today ? get it dirty ? Link to comment Share on other sites More sharing options...
bupalooga Silver Donating Members 261 Member For: 12y 2m 20d Gender: Male Location: Griffith NSW Posted 20/01/22 01:12 AM Share Posted 20/01/22 01:12 AM Last day of isolation. Was finally able to do the iso project I bought early 2020. Gramps looking classy with the restored and polished 5 poster. Just need a set of 9" spotties and a uhf aerial that's not connected to anything to finish the look.Work truck got the full Bowdens paint cleanse, wax, sealant and interior detail. 2 Link to comment Share on other sites More sharing options...
Slowxr6t Member 561 Member For: 6y 22d Location: New zealand Posted 20/01/22 08:45 AM Share Posted 20/01/22 08:45 AM My fgx with gt3582r has a ts 45mm hypergate plumbed onto externally gated 1.06 housing, I wasn't sure what psi spring was in it. It was getting 10 psi boost by 2500rpm but not getting to 13-14psi till about 5000rpm, I knew something wasn't right. I took gate off and tested it with a air compressor, regulator and a accurate air guage. I could see it just cracking open at 9psi and by 12psi nearly wide open so I thought well it must be bleeding off into exhaust so no wonder it takes so long to make 13-14psi. I went to town, guy at performance shop said my spring looked like a 7osi spring, I bought a 10psi spring, put that in and tested it with air. 13psi it's cracking open now and 15psi it's wide open. Put it on car and went for a drive, wow what a difference, 15psi max now at about 4000rpm and goes heaps harder, way more peppy and responsive. Major improvement! My question is I thought the stock ecu/boost control wouldn't have cared about a light spring and would've just boosted up quickly. Obviously you've gotta get the spring rate right for the tune/boost level desired and tuned for with the barra ecu. Also it is tuned for 14psi but another question is, now that I'm getting full boost earlier will I need a retune because of more midrange power or will ecu adjust itself? I still get 10psi at 2500rpm but it rushes to 15psi now and gets there 1000-1500rpm earlier than before. Cheers guys. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now