BeerTurbo Donating Members 241 Member For: 6y 6m 19d Posted 08/06/21 08:08 AM Share Posted 08/06/21 08:08 AM not today, but the gone weekend. hunting the misfire from last event. ordered new coils for fun. new plugs went in too. checked the injectors as I had left e85 in the system while it sat for +5 months and I was curious. luckily was just the pre injector filters, replaced them and was fine. this was a an annoyance. lucky a local store had replacements. swap diff ratio, required moving the twin bracket over. this was an annoyance. brake pads were non existent. so full new sets for both. leave the rusty rotor, cause yolo? can ran loads better but would ocasionally still misfire. it pushed alot of coolant so I guess this weekend is compression check. when I removed the sparks two had verry white tips so it would have been a bit lean last event while running the clogged injectors. fun times ahead. 1 Link to comment Share on other sites More sharing options...
NA_TURBO Member 532 Member For: 9y 1m 20d Gender: Male Location: Mildura Posted 17/06/21 11:37 AM Share Posted 17/06/21 11:37 AM Thought I'd try and polish the wheels on the old EA... More work than I thought. Going to need a few cones to finish them all, that's one cone per wheel haha Link to comment Share on other sites More sharing options...
biddie_fiddler [IMPULSIV3] Donating Members 1,374 Member For: 5y 7m 30d Gender: Male Location: Perth, WA Posted 17/06/21 11:52 PM Share Posted 17/06/21 11:52 PM What uhhh, cones we talking about here... 😉🤣 Link to comment Share on other sites More sharing options...
k31th less WHY; more WOT Site Developer 28,998 Member For: 16y 7m 18d Gender: Male Location: Melbourne Posted 18/06/21 12:07 AM Share Posted 18/06/21 12:07 AM I was wondering how many he'd smoked... Link to comment Share on other sites More sharing options...
NA_TURBO Member 532 Member For: 9y 1m 20d Gender: Male Location: Mildura Posted 18/06/21 12:10 AM Share Posted 18/06/21 12:10 AM I need a few today... Haha Link to comment Share on other sites More sharing options...
Cbaker New Member 14 Member For: 5y 4m 6d Posted 10/07/21 12:36 PM Share Posted 10/07/21 12:36 PM Starting to do some cosmetic stuff. New tint to replace the old peeling stuff. Off to body works next to fix one decent ding and a couple of paint scratches when the annual car stimulus package comes in.. I mean tax return 1 Link to comment Share on other sites More sharing options...
Slowxr6t Member 560 Member For: 5y 11m 24d Location: New zealand Posted 20/08/21 12:44 AM Share Posted 20/08/21 12:44 AM Not today, but yesterday, I finished fitting and bleeding my new brakes, dba 355mm rotors and brembo 6 piston calipers on front and safe brake braided lines all round. I went for a cruise and bedded in new brakes. I did 8 100kph to 20kph stops and then let them cool by driving for 10 minutes then did 3 140 to 20 stops and let them cool. Twice low oil pressure popped up on dash for 2 seconds under hard braking, must have been the gforces. I also just fitted a saas oil pressure adapter into the turbo oil feed fitting on block and the factory oil pressure sensor now is screwed into the end of the saas adapter so is now 5 cm further out from the block from where it used to be, so probably reads pressure a bit slower with oil rushing around. The brakes are really awesome now, before the stockers struggled to slow the boat down from speed. I also managed to fit in a decent power slide, 1 for the covid lockdown. Lol 1 Link to comment Share on other sites More sharing options...
k31th less WHY; more WOT Site Developer 28,998 Member For: 16y 7m 18d Gender: Male Location: Melbourne Posted 20/08/21 12:46 AM Share Posted 20/08/21 12:46 AM pics? Link to comment Share on other sites More sharing options...
Slowxr6t Member 560 Member For: 5y 11m 24d Location: New zealand Posted 20/08/21 08:07 AM Share Posted 20/08/21 08:07 AM My derale thermostatic sandwich block with threaded ports for oil cooler lines. Also saas brass adapter for saas oil pressure sensor for oil pressure gauge is screwed into the turbo oil feed line with stock oil pressure sensor screwed into the other end. 2 Link to comment Share on other sites More sharing options...
Slowxr6t Member 560 Member For: 5y 11m 24d Location: New zealand Posted 20/08/21 08:12 AM Share Posted 20/08/21 08:12 AM Managed to score a set of fpv metallic grey wheels, not cheap but awesome and strong, didn't want to buy cheap wheels that may give me grief. @k31th there you go, I was about to say it was to much hard work to upload pics but I got my 11 yr old son tech whiz to do it for me. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now