Puffwagon Trust me bro... Gold Donating Members 16,045 Member For: 9y 11m 11d Gender: Male Location: South Australia Posted 27/01/17 12:49 PM Share Posted 27/01/17 12:49 PM Bro do you even compressor map? Link to comment Share on other sites More sharing options...
BAXRTUTE Gold Donating Members 2,639 Member For: 8y 8m 22d Posted 27/01/17 12:51 PM Share Posted 27/01/17 12:51 PM 1 minute ago, arronm said: Factory F6 turbo, engine has a lot of mods, will make 500 easy. E85 of course Hmmmm ill be keen to see this result mate, Though wouldnt it be better to get a new gtx gen 2 and not risk hurting the block? Those new gen 2 76s will get 500rw and awesome spool everywhere. Id have one if I was a months slower in buying the turbo I did Link to comment Share on other sites More sharing options...
Puffwagon Trust me bro... Gold Donating Members 16,045 Member For: 9y 11m 11d Gender: Male Location: South Australia Posted 27/01/17 12:54 PM Share Posted 27/01/17 12:54 PM (edited) The block doesn't gaf. The compressor and iat are what matter in this case. Edit: I spose you meant rods. Edited 27/01/17 12:57 PM by Puffwagon Link to comment Share on other sites More sharing options...
arronm Dropping a turd Gold Donating Members 9,520 Member For: 17y 2m 13d Gender: Male Location: Perth Posted 27/01/17 12:55 PM Share Posted 27/01/17 12:55 PM (edited) Hurt the block, Engine is fully built, cosworth pistons , billet crank, etc. Capable of lots of power Edited 27/01/17 01:53 PM by arronm Link to comment Share on other sites More sharing options...
BAXRTUTE Gold Donating Members 2,639 Member For: 8y 8m 22d Posted 27/01/17 12:55 PM Share Posted 27/01/17 12:55 PM 3 minutes ago, arronm said: that's cause you been around for 9 months. More to it, than what you read. Lots more to it, Though over this 9mths ive been on here ive read over fark loads and leant a little... Be great to see it work mate, just think there is a smarter solution for not a huge out lay Cough gen 2 cough cough Link to comment Share on other sites More sharing options...
arronm Dropping a turd Gold Donating Members 9,520 Member For: 17y 2m 13d Gender: Male Location: Perth Posted 27/01/17 12:57 PM Share Posted 27/01/17 12:57 PM True, but I want to take the factory turbo to the limit Link to comment Share on other sites More sharing options...
BAXRTUTE Gold Donating Members 2,639 Member For: 8y 8m 22d Posted 27/01/17 12:59 PM Share Posted 27/01/17 12:59 PM (edited) U deep pocket short armed fark Can we get a betting syndicate going on what it will make? When is this tune happening? I'll kick it off at 465rwkw @23.5psi and pushing chit up hill hard from 5k rpm Edited 27/01/17 01:03 PM by BAXRTUTE Link to comment Share on other sites More sharing options...
arronm Dropping a turd Gold Donating Members 9,520 Member For: 17y 2m 13d Gender: Male Location: Perth Posted 27/01/17 01:04 PM Share Posted 27/01/17 01:04 PM Yep, do that then move on.. Doubt many turbo falcons are making 400rwkw on 15psi on 98.. Shows the difference things like head work make. Lots and Lots of hours have gone into this engine. Link to comment Share on other sites More sharing options...
Puffwagon Trust me bro... Gold Donating Members 16,045 Member For: 9y 11m 11d Gender: Male Location: South Australia Posted 27/01/17 01:05 PM Share Posted 27/01/17 01:05 PM Just now, arronm said: True, but I want to take the factory turbo to the limit Weld it shut. But why bother? You'll just have skids then high iat's, egt's and backpressure that a kiwi would envy. So far we've seen that it comes on slow in your current configuration despite lack of tune details. Fark it off and get something that has the right amount of lag to keep grip but can actually hold the mid and top end you desire. Link to comment Share on other sites More sharing options...
Box stock T. Member 1,384 Member For: 9y 9m 2d Posted 27/01/17 01:07 PM Share Posted 27/01/17 01:07 PM 9 minutes ago, arronm said: Hurt the block, Engine is fully build, cosworth pistons , billet crank, etc. Capable of lots of power Nizpro Typhoons definitely did get the ton spent on them back in the day when they were intended to be exported to the UK. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now