arronm Dropping a turd Gold Donating Members 9,520 Member For: 17y 1m 26d Gender: Male Location: Perth Posted 05/04/14 09:52 AM Share Posted 05/04/14 09:52 AM Pulled it apart and put it back together with new stuff.But I need to do some work on the cold side as the piping is hard against the bumper underneath. I might have the 2 45 deg silicone joiners if the opposites position.I see a drop saw, Must be a Rapids cooler. 3 Link to comment Share on other sites More sharing options...
Wenier Donating Members 1,736 Member For: 14y 11m 5d Gender: Male Location: Christchurch, New Zealand Posted 05/04/14 10:53 AM Share Posted 05/04/14 10:53 AM No its plazmaman, and the drop saw wasn't used. Just happened to be lying around in the garage wanting to be in on the action. Link to comment Share on other sites More sharing options...
Kosij Donating Members 2,045 Member For: 13y 4m 12d Gender: Male Posted 05/04/14 01:05 PM Share Posted 05/04/14 01:05 PM Demolished a set of et streets!Not made for the streets Washed itThrashed it 1 Link to comment Share on other sites More sharing options...
Spyathe Donating Members 872 Member For: 11y 1m 23d Gender: Male Posted 06/04/14 03:51 AM Share Posted 06/04/14 03:51 AM Big job today!Replacing transmission, tailshaft centre bearing, rear main seal, torque converter seal and extension housing sealOh and putting in a trans cooler O.O 1 Link to comment Share on other sites More sharing options...
Wenier Donating Members 1,736 Member For: 14y 11m 5d Gender: Male Location: Christchurch, New Zealand Posted 06/04/14 07:47 AM Share Posted 06/04/14 07:47 AM Changed front springs from the Kings to cobras with a 20mm lift. So now 20mm below factory but 20mm up from the kings. Time to figure out height of rear and get the leafs out and reset. Link to comment Share on other sites More sharing options...
Bellato Donating Members 2,713 Member For: 14y 2m 3d Posted 06/04/14 07:53 AM Share Posted 06/04/14 07:53 AM Drove to Sydney, got rained on, drove back to Canberra.. Link to comment Share on other sites More sharing options...
Bulletime Donating Members 937 Member For: 13y 11m 14d Gender: Male Posted 06/04/14 10:56 AM Share Posted 06/04/14 10:56 AM There isn't a not like button unfortunately Link to comment Share on other sites More sharing options...
Kosij Donating Members 2,045 Member For: 13y 4m 12d Gender: Male Posted 06/04/14 11:00 AM Share Posted 06/04/14 11:00 AM Bellato I feel ya,I drove 6hours got a tune, waittes for full throttle Friday and bam rain :( second event in a row canned! Link to comment Share on other sites More sharing options...
discostig Manual mode ________________________ All day, erryday Donating Members 13,798 Member For: 17y 28d Gender: Male Location: Probably above atmospheric pressure Posted 06/04/14 02:03 PM Share Posted 06/04/14 02:03 PM (edited) Old oil and filter outNew oil and filter in (filter courtesy of turbotrana at my 30th, thanks mate hahaha)New belt on (fans out this time, slowly learning)Clean throttle body/butterfly and crossover piping, lube pullies as best I canPut it all back together and ready to go for a test drive, let's check torque of wheel nuts first. Should take all of 2 minutes.Mofo.New mission, remove all 4 lock nuts without a functioning lock nut key. Remembered the tip I've read on here any times before, bashing on sockets! 22mm was too tight...7/8" socket was perfect. After 5 minutes of trying to pry the thing back out of the socket to get the other 3, I had a rethink and remembered sockets have a hole through them Grab a bigger deep socket to brace it against and for the nut to fall into loosely (a tip I worked out after the first go with a 22mm deep socket that got stuck on it...doofus)Now I know why I didn't throw out my broken $2 ratchet. Re-purposed as a ram rod! Also decided to place some metal underneath after digging a chunk out of the concrete floor on my first go at it.I'm glad to be rid of the lock nuts. They are piss easy for thieves to remove and can only stop me from changing a wheel in the rain on the way to a wedding or something. Edited 06/04/14 02:08 PM by -SteveR- Link to comment Share on other sites More sharing options...
arronm Dropping a turd Gold Donating Members 9,520 Member For: 17y 1m 26d Gender: Male Location: Perth Posted 06/04/14 02:13 PM Share Posted 06/04/14 02:13 PM (edited) You got it Steve, that's exactly how you do it.Hey Steve are 2 of your wheels +27 rear use only. My origin FPV wheels were like that. You can tell as the wheel nuts are different lenghts Edited 06/04/14 02:16 PM by arronm Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now