Jump to content

Calder Drags?


bloan

Recommended Posts

  • Replies 71
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

  • Member
  • Member For: 21y 2m 18d
  • Location: South of Melbourne, near the sea

A disappointing evening for the T and big horespower! Both contenders broke their transmissions (not sure in what way) and don't think any times were recorded. So it looks like they have both found the limits of the auto T's drive line :(

However, good to see both cars in the flesh.

Link to comment
Share on other sites

  • Member
  • Member For: 21y 6m 21d
  • Location: Ballarat
Does any one know weather the drags were run last night & if so more importantly did APS run their Ute & what times they ran???

APS did 11.34@125mph before trashing the trans, they also recorded a terminal speed as high as 127mph as well. Nizpro only managed to do one pass with a time in the 12's @105mph.

Link to comment
Share on other sites

  • potty trained
  • Lifetime Members
  • Member For: 21y 8m 25d
  • Gender: Male

it was a good night ...

Nizpro ran very early (before most got there which defeat the purpose a little :spit: )

APS ran a number of strong passes in the low 11s with good speed and finally said goodbye to the tranny in a encore pass :(

I like to see Nizpro and APS side by side ... first over the line :lol:

anyways ... with over 400rwkw the tranny was still working (sort off :thumbsup: )

well done guys :blush:

Link to comment
Share on other sites

  • Lifetime Members
  • Member For: 22y 3m 9d
  • Gender: Male
  • Location: South Coast NSW

Interesting ... what happened to all the promos about autos being the best for the strip, not breaking etc.? I know these cars are putting out way above their stock torque but some manuals are also and I haven't heard of any of them breaking yet. I seem to remember Steve's (Redcliffe Dyno) is a manual and he is also on record as saying in his opinion the manual will stand a lot more torque than everyone else has been saying.

GO THE MANUALS :lol: :lol:

Low 11s are good though eh? even for an auto :lol:

Link to comment
Share on other sites

  • Premium Donating Member
  • Donating Members
  • Member For: 21y 2m 30d
  • Gender: Male
  • Location: If it says ONLINE below, in front of the computer, if not, tearin' up some bitumen!
Interesting ... what happened to all the promos about autos being the best for the strip, not breaking etc.? I know these cars are putting out way above their stock torque but some manuals are also and I haven't heard of any of them breaking yet. I seem to remember Steve's (Redcliffe Dyno) is a manual and he is also on record as saying in his opinion the manual will stand a lot more torque than everyone else has been saying.

GO THE MANUALS :lol: :lol:

Low 11s are good though eh? even for an auto :lol:

Where are the manuals behind motors like these??????

Steve's opinion is just that, his opinion! No disrespect to Steve, I don't know him, but has he been running 11's week after week in a manual? Maybe, but not that I've heard? When he has, then his opinion becomes fact, but not before.

Link to comment
Share on other sites

  • Bloody Orange Team (BOT)
  • Donating Members
  • Member For: 21y 6m 28d
  • Gender: Male
  • Location: Canberra, Australia

I always thought dynosteve's beast had an auto gearbox..

Anyways, on to the broken transmissions. Now they have an excuse to toughen the suckers up then do a little more power increases ;)

Link to comment
Share on other sites

  • FORD FORD FORD
  • Donating Members
  • Member For: 21y 10m 2d
  • Gender: Male
  • Location: Victoria Point In Brissy's eastern side
I seem to remember Steve's (Redcliffe Dyno) is a manual and he is also on record as saying in his opinion the manual will stand a lot more torque than everyone else has been saying.

Steve's car is an Auto, he hasn't run 11's yet that I know of.

Scotty

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.



×
  • Create New...
'