xr6turboman Donating Members 588 Member For: 16y 10m 1d Gender: Male Location: New Zealand, Palmerston North Posted 26/02/12 08:45 PM Share Posted 26/02/12 08:45 PM Hi,Went to 1/8 mile drags yesterday had lots of fun but my times were pretty pathetic, best I could manage was 1/8 in 10.02 at 137kph car has 345rwkw 6 sp manual and a herrod sure shift .. running 20/30/245 falken fk452 on 25.5psi ... I was getting an alright initial jump but would loose massive traction in first and into second and by the time I get to third 1/8 mile was basicaly over. I did manage one good run until I went for 3rd an put it in 1st and compression locked the rears ended up coasting over line with clutch in would have liked to see what that time was ..ANyway I would some advise on ways to improve time what rpm I should be launching at ?? would I better of getting some drag light wheels and putting some slicks on? what will I break if I do that? is there any weight that can easily be shedd that'll make a diff?? Any advice will be much appreciated..Thanks Link to comment Share on other sites More sharing options...
Brods Member 433 Member For: 14y 6m 17d Gender: Male Posted 26/02/12 09:18 PM Share Posted 26/02/12 09:18 PM Slicks plus manual = prepare for $$$$ Link to comment Share on other sites More sharing options...
rbjet Skid Machine Donating Members 1,640 Member For: 13y 8m 21d Gender: Male Posted 26/02/12 10:49 PM Share Posted 26/02/12 10:49 PM Maybe even some smaller rims on the rear as 20s are no good for traction. Slicks would be better but be prepared to snap some drive shafts. Link to comment Share on other sites More sharing options...
Wenier Donating Members 1,736 Member For: 15y 27d Gender: Male Location: Christchurch, New Zealand Posted 27/02/12 12:39 AM Share Posted 27/02/12 12:39 AM Id say some wider rears with good street tyres, maybe an 18" rim by 9.5 or 10 wide so you can get a wider foot down. 345rwkw is alot for a 245 size tyre. And as above. Link to comment Share on other sites More sharing options...
senna_T Forged Member Lifetime Members 15,818 Member For: 18y 7d Gender: Male Location: SW Sydney Posted 28/02/12 12:51 AM Share Posted 28/02/12 12:51 AM Manual is not an easy deal with these cars. Problem being that every time you change gears you have 2 tonnes worth of falcon slowing the car down when you aren't in gear accelerating...You need to slip the clutch as you come off the line so you get some road speed up before the clutch is fully engaged and transferring all the torque to the rear wheels. Also, try not to dump the clutch between gears, the smoother you are the quicker you will be! As others have said though, budget for a set of CVs... Link to comment Share on other sites More sharing options...
Dillz Three pedals are better then two.. Donating Members 15,637 Member For: 17y 8m 19d Gender: Male Location: Melbourne Posted 28/02/12 01:58 AM Share Posted 28/02/12 01:58 AM Pat with CV's for FG I read somewhere you have to replace the whole back end or something if one goes? Is this true or can you just replace an individual CV? What are they roughly anyway? Link to comment Share on other sites More sharing options...
senna_T Forged Member Lifetime Members 15,818 Member For: 18y 7d Gender: Male Location: SW Sydney Posted 28/02/12 04:11 AM Share Posted 28/02/12 04:11 AM Nah, the rear is the same in BA/BF/FG (except for diff bush) so you can just change the one shaft. Just make sure you buy a new Hub locking nut and a new diff-axle seal when you change a CV, these are only cheap from Ford anyway. I haven't found anyone aside from Albins that do just a CV knuckle upgrade, everyone else does complete shafts for mega $$$$ Link to comment Share on other sites More sharing options...
Dillz Three pedals are better then two.. Donating Members 15,637 Member For: 17y 8m 19d Gender: Male Location: Melbourne Posted 28/02/12 04:20 AM Share Posted 28/02/12 04:20 AM So would something this fit an FG then?http://www.ebay.com.au/itm/FORD-FALCON-REAR-DRIVESHAFT-BA-BF-V8-TURBO-MODELS-R-H-SIDE-02-2007-XR6T-XR8-/290676652605?pt=AU_Car_Parts_Accessories&hash=item43adadba3d$200 a sides not too bad, thought they would be more. Link to comment Share on other sites More sharing options...
rbjet Skid Machine Donating Members 1,640 Member For: 13y 8m 21d Gender: Male Posted 28/02/12 04:40 AM Share Posted 28/02/12 04:40 AM (edited) Wouldn't you be better off just buying second hand shafts from the wreckers if you weren't going to go the billet route?Heard the after market ones aren't as good as the factory items either.I dunno if the falcon's are the same but my cousin just replaces his with second hand ones for about $30 when ever he snaps a shaft in his vy ute. Edited 28/02/12 04:41 AM by rbjet Link to comment Share on other sites More sharing options...
senna_T Forged Member Lifetime Members 15,818 Member For: 18y 7d Gender: Male Location: SW Sydney Posted 28/02/12 05:49 AM Share Posted 28/02/12 05:49 AM The Late model camira ones are way stronger than the falcon shafts, plus they don't vary between LSD and open diffs, anything out of anything will fit. Dillz - stick with genuine until someone tries those ones out! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now