adrian_celati Donating Members 82 Member For: 15y 10m 24d Gender: Male Posted 29/11/11 09:23 AM Share Posted 29/11/11 09:23 AM Hi all, just about to change the coolant in my BFII XR6T auto and was wondering where the coolant bleed screw is?Cheers. Link to comment Share on other sites More sharing options...
RHR BOOST Moderating Team 5,698 Member For: 21y 2m 29d Gender: Male Location: Southern Highlands NSW Posted 29/11/11 09:37 AM Share Posted 29/11/11 09:37 AM If its the same as fg it's on the lower right hand side of the radiator. Might need to remove the air intake snorkel to get to it Link to comment Share on other sites More sharing options...
adrian_celati Donating Members 82 Member For: 15y 10m 24d Gender: Male Posted 29/11/11 09:59 AM Author Share Posted 29/11/11 09:59 AM To bleed air out of the system wouldn't it need to be at the top of the cooling system somewhere? Link to comment Share on other sites More sharing options...
Smoke them tyres Member 557 Member For: 16y 11m 12d Gender: Male Location: Brisbane Posted 01/12/11 09:53 PM Share Posted 01/12/11 09:53 PM coolant tank does the job automatically........it's the highest point in the system. Link to comment Share on other sites More sharing options...
Paulie2256 Donating Members 7,441 Member For: 16y 12d Gender: Male Location: SE Melbourne Posted 02/12/11 01:34 AM Share Posted 02/12/11 01:34 AM It's on the bottom right side of the radiator. Don't need to remove anything to get to it if your arms/hands fit in there. Link to comment Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,323 Member For: 19y 2m 11d Gender: Male Location: Perth Posted 02/12/11 01:44 AM Share Posted 02/12/11 01:44 AM Thats the drain not the bleed. Run the car up too temp with the coolant reservoir cap off and the heater on and it will bleed itself. Then check the level the next morning. Helps if you pack the car with the front end elevated of jack up the front a couple of inches Link to comment Share on other sites More sharing options...
Paulie2256 Donating Members 7,441 Member For: 16y 12d Gender: Male Location: SE Melbourne Posted 02/12/11 02:53 AM Share Posted 02/12/11 02:53 AM (edited) Whoops. Well in that case I agree with you. When I changed the coolant I just poured the coolant in the reservoir until full, started the engine and heater full blast then kept topping up until the level didn't move any more. Then the next day top up if needed and you are done. Edited 02/12/11 02:54 AM by Paulie2256 Link to comment Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,323 Member For: 19y 2m 11d Gender: Male Location: Perth Posted 02/12/11 02:59 AM Share Posted 02/12/11 02:59 AM Buuuuuuuuuuuuut If the OP has confused his drain with his bleed, Paulie is 100% correct on the location of the Drain plug/bung/screw Link to comment Share on other sites More sharing options...
mic Donating Members 1,725 Member For: 16y 10m 16d Gender: Male Posted 02/12/11 05:08 AM Share Posted 02/12/11 05:08 AM no air bleed in these. that's only 4 old sh*t. Link to comment Share on other sites More sharing options...
discostig Manual mode ________________________ All day, erryday Donating Members 13,798 Member For: 17y 10d Gender: Male Location: Probably above atmospheric pressure Posted 02/12/11 05:23 AM Share Posted 02/12/11 05:23 AM Search seems to find 0 results for "coolant", so...which brand if any is recommended by those in the know? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now