Bomber Carnage on the Garage Floor Donating Members 3,994 Member For: 14y 7m 15d Gender: Male Location: Gold Coast Posted 22/02/14 10:45 AM Author Share Posted 22/02/14 10:45 AM You still running the 750 old_mate? Link to comment Share on other sites More sharing options...
old_mate Member 767 Member For: 18y 10m 13d Gender: Male Location: Brisbane Posted 23/02/14 12:26 AM Share Posted 23/02/14 12:26 AM Sure am mate. Link to comment Share on other sites More sharing options...
Bomber Carnage on the Garage Floor Donating Members 3,994 Member For: 14y 7m 15d Gender: Male Location: Gold Coast Posted 23/02/14 08:18 AM Author Share Posted 23/02/14 08:18 AM What did you end up with after tune was sorted and at what boost old_mate? Link to comment Share on other sites More sharing options...
old_mate Member 767 Member For: 18y 10m 13d Gender: Male Location: Brisbane Posted 24/02/14 01:37 PM Share Posted 24/02/14 01:37 PM 380rwkw with a turbo side intake at 18psi; 373rwkw with the crossover at the same boost as I drive it everyday. Needs a tweak on actuator preload at some point and a bit of E85 down its throat however I might wait until I have done oil pump gears and the ZF and tailshaft before all of that. Link to comment Share on other sites More sharing options...
Bomber Carnage on the Garage Floor Donating Members 3,994 Member For: 14y 7m 15d Gender: Male Location: Gold Coast Posted 26/02/14 12:12 PM Author Share Posted 26/02/14 12:12 PM ^^^ yes it never stops mate 1 Link to comment Share on other sites More sharing options...
Bomber Carnage on the Garage Floor Donating Members 3,994 Member For: 14y 7m 15d Gender: Male Location: Gold Coast Posted 27/02/14 10:56 AM Author Share Posted 27/02/14 10:56 AM MTA is doing a billet front wheel conversion with his spec cartridge for a mate. I'm going to see how that goes. In all honesty, if that makes a solid 330 on 98 I might go that way also as it means no other hardware changes (except actuator) and I'd maybe go that little further and port and flapper it. These things are like drugs and you've got to decide when to step off or keep spending. I'm worried about input shafts and stuff if I go bigger. The little turbo upgrade with E85 would sh*t 350rwkw in which was my goal. Would have mad spool also with a decent bearing pack to support it. Link to comment Share on other sites More sharing options...
Bomber Carnage on the Garage Floor Donating Members 3,994 Member For: 14y 7m 15d Gender: Male Location: Gold Coast Posted 18/03/14 10:29 AM Author Share Posted 18/03/14 10:29 AM Looking for a donor GT3576R. Can have rooted core. Really just chasing a rear housing and cover. Link to comment Share on other sites More sharing options...
old_mate Member 767 Member For: 18y 10m 13d Gender: Male Location: Brisbane Posted 18/03/14 11:34 AM Share Posted 18/03/14 11:34 AM Could even use a stuffed GT3582R if you just need the housings? Link to comment Share on other sites More sharing options...
Bomber Carnage on the Garage Floor Donating Members 3,994 Member For: 14y 7m 15d Gender: Male Location: Gold Coast Posted 22/03/14 06:01 AM Author Share Posted 22/03/14 06:01 AM Yes I have found one mate but bit concerned about getting a B series housing. This one is of a BA also. Reckons no cracks so will have a look. Link to comment Share on other sites More sharing options...
Bomber Carnage on the Garage Floor Donating Members 3,994 Member For: 14y 7m 15d Gender: Male Location: Gold Coast Posted 26/03/14 11:54 PM Author Share Posted 26/03/14 11:54 PM Slight change of plans. Either way I go the valve springs will become an issue at some point. I'd hate to get the call mid tune and be told they 'no likey' the new turbo and have to find the extra coin straight away, or pull the tune right back.So, the plan is to do them now. Slip the ID1000's in with the herrod intank and tickle the 98 tune with maybe an E85 for poo and giggles. The ZF tune will get a tweak as well. Want to put some fart back in and soften the shifts a little. It's not too harsh but want to preserve it as best I can and minimise the chance of shaft failure. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now