bionicxr6t05 Bronze Donating Members 2,216 Member For: 13y 3m 26d Gender: Male Posted 04/05/12 09:26 AM Share Posted 04/05/12 09:26 AM Hahahahaha love it, mines zf auto I get good traction in 3rd rolling on boost but if I just mash the pedal in 2nd itl spin til I tell it to stop Link to comment Share on other sites More sharing options...
turbowelshy89 Member 147 Member For: 14y 3m 27d Posted 04/05/12 02:01 PM Share Posted 04/05/12 02:01 PM Bahaha there's already a club boys its called 'The pin is pulled'. But I had to leave as mine engine decided to go all new and start changing the compression ratio on number one lol. As long as u look after it ie services and so forth I reckon it should hold for a while lol...Ps while= length of a piece of string... LokSent from my HTC Velocity 4G using Tapatalk 2 Link to comment Share on other sites More sharing options...
rhys86 Donating Members 443 Member For: 17y 10m 24d Gender: Male Location: Wollongong Posted 19/05/12 08:28 AM Share Posted 19/05/12 08:28 AM What mods have you done to it??Nice power by the way. Link to comment Share on other sites More sharing options...
601Turbz Member 111 Member For: 14y 2m 16d Gender: Male Posted 12/07/12 11:08 AM Share Posted 12/07/12 11:08 AM What mods have you done to it??Nice power by the way.Kroozin give us a list of mods that you have done, Keen to get my BF MK11 to 350+ rwkw. Cheers Link to comment Share on other sites More sharing options...
Kroozin Menace Donating Members 1,990 Member For: 13y 7m 1d Gender: Male Location: Sydney Posted 12/07/12 11:57 AM Author Share Posted 12/07/12 11:57 AM Hey rhys86 and 601Turbz,Sorry for the late reply must have missed it.Mods when I accomplished 348rwkw were:3" intake custom made. Goes under modded battery tray down infront of battery thru 95mm hole to big FO pod located under the battery in the front bar.wastegate ported and 12lb act. fitted.4" dump to 5" 100cell cat to twin 2.5" 2 hotdogs, 1 rear sports mufflerupgraded valve springsrapids hot side piping1000hp plazmaman intercooler3" cold side pipingthrottle body relocation kit (from orangeute888... bloody bargain, do it if your on a budget and dont wanna go a $1200 plenum. Certainly beats the run around style IMO)Redrilled standard injectorsWalbro intank pumpYa probably dont need all that stuff to make the mark but this is the route I have chosen.Later on I fitted a plazzy surge tank with an 044 and decided to run eflex which now has me sitting at 406rwkw or 411rwkw depends whos dyno ya wanna go by. We had to stop there as the inj. are seriously maxxed and im a fool to have not changed them yet.Still planning on getting the ID1000 injectors to push a little further on the skinny rods... phuck it why not If ya havent got inj. yet seriously look into getting some ID1000's from a reputable shop..I.e your tuner. it'll set ya back roughly 2-300bux more than your fleabay 60lb's.. but you will be glad later when you dont have to spend the money twice.IMO the 60lb's off ebay will be any bodys guess if they are properly flow matched or not and will end being possibly too small later on.I'd hate to have 1 cyl. running leaner than the others and not know about it until its too late. Link to comment Share on other sites More sharing options...
bionicxr6t05 Bronze Donating Members 2,216 Member For: 13y 3m 26d Gender: Male Posted 15/07/12 12:59 AM Share Posted 15/07/12 12:59 AM Hey kroozin what boost you running to get that figure? Link to comment Share on other sites More sharing options...
Kroozin Menace Donating Members 1,990 Member For: 13y 7m 1d Gender: Male Location: Sydney Posted 15/07/12 06:46 AM Author Share Posted 15/07/12 06:46 AM 19lb mate. Though we had to dog the mid region with bucket loads of fuel (in the low 10's) so up top stayed in around 12.5afr.My decision at the time to push the inj. like that.... They are seriously maxed ATM 680cc. Didn't think I was Gunna phuck around this long getting the ID's.So in sayin all that the scale of power would be better with the right inj. fitted. Link to comment Share on other sites More sharing options...
bionicxr6t05 Bronze Donating Members 2,216 Member For: 13y 3m 26d Gender: Male Posted 15/07/12 07:56 AM Share Posted 15/07/12 07:56 AM Nice I have 80lb's so have a bit of headway atm waitin for my external gate setup then goin 20+psi on the baby rods Link to comment Share on other sites More sharing options...
Kroozin Menace Donating Members 1,990 Member For: 13y 7m 1d Gender: Male Location: Sydney Posted 15/07/12 09:43 AM Author Share Posted 15/07/12 09:43 AM Nice mate, look forward to seein ya results.What turbo are you going to? Link to comment Share on other sites More sharing options...
bionicxr6t05 Bronze Donating Members 2,216 Member For: 13y 3m 26d Gender: Male Posted 15/07/12 09:57 AM Share Posted 15/07/12 09:57 AM Stock mate doing my own etm style kit using turbosmart hypergate and eboost street Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now