relentless xr6 Member 363 Member For: 14y 2m 24d Gender: Male Location: Sydney Posted 31/07/11 11:14 AM Share Posted 31/07/11 11:14 AM +1 for plazmaman I hope you pull a good figure and back it up at strip. all I can say is meh about intune had bad vibes when I rocked up to buy parts so I went to auto tech lol Link to comment Share on other sites More sharing options...
dre Resident idiot. Donating Members 2,068 Member For: 14y 5m 8d Gender: Male Location: Melbourne Posted 31/07/11 11:27 AM Share Posted 31/07/11 11:27 AM I went with plazmaman gear for my car, no regrets from me. keep us informed about how it goes with the tune. Ali will do a great job Link to comment Share on other sites More sharing options...
P_BA_XR6 Member 271 Member For: 16y 8m 27d Gender: Male Location: Castle Hill Posted 31/07/11 12:10 PM Share Posted 31/07/11 12:10 PM (edited) yer they tuned my car once with the throttle body clamp not on properly once before and told me the motor was shot..I was absolutely gutted after I was told I might aswell leave it there and spend 10k on a new built motor drove hm pi$$ed off, got hm opened the bonnet said what the drove back and got it retuned made another 40kw with the hose fitted with no engine probsKeen to get it all tuned up im over driving around off boost everywhere. Look forward to a good result. Thanx guysreason for edit: oops im on my brothers computer Edited 31/07/11 12:11 PM by P_BA_XR6 Link to comment Share on other sites More sharing options...
discostig Manual mode ________________________ All day, erryday Donating Members 13,798 Member For: 17y 3m 4d Gender: Male Location: Probably above atmospheric pressure Posted 01/08/11 12:04 AM Share Posted 01/08/11 12:04 AM Don't drive through puddles with that low of an intake, bloke here in the west busted his engine pretty badly after drawing in water from down there, also I'm told it picks up more dirt and grit from the road surface too. Mainly avoid the puddles though! Link to comment Share on other sites More sharing options...
.BLKPHN. Bronze Donating Members 283 Member For: 14y 6d Gender: Male Posted 01/08/11 02:00 AM Share Posted 01/08/11 02:00 AM I have a 1800hp plaz cooler 100mm core option and it is a blooooddy tight fitmove radiator cut reinforcment bar and bottom of front bar as they sit bloody low and cant get front bar on without cutting it Link to comment Share on other sites More sharing options...
Kroozin Menace Donating Members 1,990 Member For: 13y 10m 7d Gender: Male Location: Sydney Posted 01/08/11 08:51 AM Author Share Posted 01/08/11 08:51 AM Thanks Steve I took the under tray off the bumper today and I can see what you mean. I might have to make up some sort of splash guard on the inner side somehow to try and minimise the issue. BLKPHN have ya got any pics of it fitted up? that's sux about all the cutting dude but I know what its like once ya start ya just wanna get it done pretty much to the point of whateva it takes.lolHow come you went the 1800hp cooler, what power are ya aiming for? Link to comment Share on other sites More sharing options...
bossmang FREAKY Donating Members 12,435 Member For: 15y 2m 3d Gender: Male Location: Melbourne Posted 01/08/11 09:08 AM Share Posted 01/08/11 09:08 AM nice work kroozin.can you get the plaz gear without their logo printed on the front of the cooler? Link to comment Share on other sites More sharing options...
Henz Tampon inserted, Auto Acquired, next purchase a new handbag Donating Members 9,946 Member For: 16y 11m 8d Gender: Male Location: Vic Posted 01/08/11 09:11 AM Share Posted 01/08/11 09:11 AM Sure can. Actually the cooler doesn't seem as in your face on this as they normally do. Is it just raw finish? Link to comment Share on other sites More sharing options...
Kroozin Menace Donating Members 1,990 Member For: 13y 10m 7d Gender: Male Location: Sydney Posted 01/08/11 09:26 AM Author Share Posted 01/08/11 09:26 AM Yeah bud raw finish. I was going to get the black powder coated one but my cousin at http://www.jnjperformance.com.au/ are going to anodise it black (think that's how u spell it) later on plan on ceramic coating the turbo housing and zorst manifold too.Hey while im on the subject would ceramic coating the zorst and turbs effect the afr's or anything? Link to comment Share on other sites More sharing options...
.BLKPHN. Bronze Donating Members 283 Member For: 14y 6d Gender: Male Posted 01/08/11 09:42 AM Share Posted 01/08/11 09:42 AM hey croozin yer mate went the biggest couse my aim after my build is over 1000rwhp and not stoping till I get it haha so I went over kill but I no it will do the job and all the big hp cars run themthis is it fitted but still rubing so neet to cut out reinforcemeny bar and it hangs bloody low so end tanks will hang below front bar a few mill so need to cut sections out of that also hahah should be worth it buthttp://imageshack.us/photo/my-images/849/img0189e.jpg/ Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now