Tocchi Sandtrap Motorsport Donating Members 2,055 Member For: 16y 4m 27d Gender: Male Location: Perth Posted 10/02/11 12:57 AM Author Share Posted 10/02/11 12:57 AM ok thank you for that I will try to have a look at that today Link to comment https://www.fordxr6turbo.com/forum/topic/73162-low-spark/page/2/#findComment-1079811 Share on other sites More sharing options...
IH8TOADS Silver Donating Members 3,618 Member For: 19y 9m 13d Gender: Male Location: OZ Posted 10/02/11 05:16 AM Share Posted 10/02/11 05:16 AM I've got spare tested coils at home you can try before forking out on a new set. PM if u can be bothered trying. Link to comment https://www.fordxr6turbo.com/forum/topic/73162-low-spark/page/2/#findComment-1079886 Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,331 Member For: 19y 6m 28d Gender: Male Location: Perth Posted 10/02/11 05:37 AM Share Posted 10/02/11 05:37 AM or ring these guys and say "oh hai guyz please sell me parts make fuel go boom"....?http://www.mwignitions.com/ Link to comment https://www.fordxr6turbo.com/forum/topic/73162-low-spark/page/2/#findComment-1079890 Share on other sites More sharing options...
Tocchi Sandtrap Motorsport Donating Members 2,055 Member For: 16y 4m 27d Gender: Male Location: Perth Posted 10/02/11 07:18 AM Author Share Posted 10/02/11 07:18 AM popped into workshop today ... coils are good.so is all the below. even checked the simple stuff like general earths, and if the battery was fully charged etc. On 09/02/2011 at 10:47 AM, hiddeous said: You need to check the impedance (resistance) of the coils and make sure they are within the range of the Motec. Factory coil wiring has a permanet earth and a switch +ve, the motec needs too be setup the same way if possible ("normally" the coils have a permanent +ve feed and switched earth)Still using the factory crank angle sensor? They dont prduce a very strong signal and if the wiring too/from the sensor is close too any high current wiring (ie alternator or coil wiring) Induced current can cause erratic signals and funky timing changes.Also get the Input from the sensor check out the motec will probably need a rising edge signal and im 99% sure ford sensors are falling edge. Again this can cause erratic signalsim thinking I will need igniters, like what M&W sell. that will get the spark up.unfortunately at the moment, the technical guru for Motec (Glen Baker) is away for work, so is unreachable, so I have to wait 2 weeks before he can give some suggestions. Link to comment https://www.fordxr6turbo.com/forum/topic/73162-low-spark/page/2/#findComment-1079923 Share on other sites More sharing options...
darios typhoon Member 73 Member For: 15y 10m 21d Gender: Male Location: northern beaches Posted 10/02/11 07:21 AM Share Posted 10/02/11 07:21 AM have a look at your crank angle sensor Link to comment https://www.fordxr6turbo.com/forum/topic/73162-low-spark/page/2/#findComment-1079926 Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,331 Member For: 19y 6m 28d Gender: Male Location: Perth Posted 16/02/11 12:11 AM Share Posted 16/02/11 12:11 AM Fixed..?? Link to comment https://www.fordxr6turbo.com/forum/topic/73162-low-spark/page/2/#findComment-1081485 Share on other sites More sharing options...
Tocchi Sandtrap Motorsport Donating Members 2,055 Member For: 16y 4m 27d Gender: Male Location: Perth Posted 16/02/11 03:15 AM Author Share Posted 16/02/11 03:15 AM havent had a chance to go to the workshop since last week :(probably will head there next week, so yeah, might be able to source a cheap Motec CDI unit (worst case), so that could help Link to comment https://www.fordxr6turbo.com/forum/topic/73162-low-spark/page/2/#findComment-1081523 Share on other sites More sharing options...
Tocchi Sandtrap Motorsport Donating Members 2,055 Member For: 16y 4m 27d Gender: Male Location: Perth Posted 04/03/11 01:40 AM Author Share Posted 04/03/11 01:40 AM ok update. good news.we had low spark issues still, no matter what we did,a couple of the things were earthing - the car is solid mounted to chassis, that's a decent earth haah.and direct power from battery to start motor, so it was getting enough power.solution: get Glenn Baker the motec guru to help so what we thought were internal ignitors on the coilpacks, arent. haha.we got sparks the size of lightening bolts :Dive got to source a M&W CDI unit, which has 250mJ compared to the Motec's 150mJ unit.anybody got any contacts for M&W products? Link to comment https://www.fordxr6turbo.com/forum/topic/73162-low-spark/page/2/#findComment-1086033 Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,331 Member For: 19y 6m 28d Gender: Male Location: Perth Posted 04/03/11 01:49 AM Share Posted 04/03/11 01:49 AM No Contacts but can vouch for the quality of the gear, Have been running 2ecu ignitors and 4 of there dual output coil packs in my Rangie for over 3 years, they have copped heat, mud , dust etc etc and never missed a beat.20mm spark gap anybody :eek: Link to comment https://www.fordxr6turbo.com/forum/topic/73162-low-spark/page/2/#findComment-1086036 Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now