unclewal Donating Members 583 Member For: 14y 1m 26d Posted 07/12/11 11:06 AM Share Posted 07/12/11 11:06 AM you'll have it in the next day, Kev is brilliant, I bought one of these back in June and its spot on ! Link to comment Share on other sites More sharing options...
Dillz Three pedals are better then two.. Donating Members 15,637 Member For: 17y 5m 20d Gender: Male Location: Melbourne Posted 07/12/11 11:40 AM Share Posted 07/12/11 11:40 AM No heads up in the PW forum? Link to comment Share on other sites More sharing options...
Bomber Carnage on the Garage Floor Donating Members 3,994 Member For: 14y 6m 4d Gender: Male Location: Gold Coast Posted 07/12/11 08:32 PM Share Posted 07/12/11 08:32 PM (edited) Kev did mention he'll do that when he gets a chance Dillz. They'd only just come back from the p/coaters mate. It's only because I'd been chasing one for a couple of weeks that I knew about this. Edited 07/12/11 08:34 PM by Bomber Link to comment Share on other sites More sharing options...
Dillz Three pedals are better then two.. Donating Members 15,637 Member For: 17y 5m 20d Gender: Male Location: Melbourne Posted 07/12/11 08:36 PM Share Posted 07/12/11 08:36 PM No worries.So what's this about the coolerworx kit being smaller then the others?? Link to comment Share on other sites More sharing options...
Bomber Carnage on the Garage Floor Donating Members 3,994 Member For: 14y 6m 4d Gender: Male Location: Gold Coast Posted 07/12/11 08:44 PM Share Posted 07/12/11 08:44 PM (edited) No worries.So what's this about the coolerworx kit being smaller then the others??Not just coolerworx. Herrod, PWR, plazmaman. Basically, any pipe kit that is designed to bolt up to the standard cooler. The p/west kit runs a 76mm cold side pipe so Kev has made this elbow to suit so it connects with a straight joiner. It's no big deal - you just need a 76 - 63 stepped joiner to use the other pipe kits. Edited 07/12/11 08:45 PM by Bomber Link to comment Share on other sites More sharing options...
Bomber Carnage on the Garage Floor Donating Members 3,994 Member For: 14y 6m 4d Gender: Male Location: Gold Coast Posted 09/12/11 09:18 AM Share Posted 09/12/11 09:18 AM fitted :sungum: Link to comment Share on other sites More sharing options...
FG50T Member 568 Member For: 20y 9m 2d Gender: Male Location: Melbourne Posted 09/12/11 02:55 PM Share Posted 09/12/11 02:55 PM Wish I saw this last week. Notice any difference in throttle response? Link to comment Share on other sites More sharing options...
Bomber Carnage on the Garage Floor Donating Members 3,994 Member For: 14y 6m 4d Gender: Male Location: Gold Coast Posted 09/12/11 10:03 PM Share Posted 09/12/11 10:03 PM Haven't driven it yet mate. Just checked for leaks last night and that was it.Looking at the plastic OEM elbow this morning and you can see why they fail. They have a nasty seam line on the inside - especially around the blow off tit side. A closer inspection revelled mine had started to crack along this seam, which no doubt would have split at some point. Not so much from boost, but engine flex. They're probably ok with the OEM rubber hoses but as soon as you go hard pipe, there is more load on them. At $106 delivered, you'd be nuts not to fit one.Little tip when fitting (Henz & Stainless will like this) use a smear of lube on the sensor 'o' ring before inserting into the part. This will save you pinching or damaging the o ring. Also, when you remove it from the original, you'll need to wiggle it and twist a little to get it out - no heavy hands! Link to comment Share on other sites More sharing options...
f6mark Member 2,908 Member For: 13y 9m 1d Gender: Male Posted 09/12/11 11:44 PM Share Posted 09/12/11 11:44 PM nice job Bomber.. :sungum: Link to comment Share on other sites More sharing options...
Bomber Carnage on the Garage Floor Donating Members 3,994 Member For: 14y 6m 4d Gender: Male Location: Gold Coast Posted 10/12/11 09:34 PM Share Posted 10/12/11 09:34 PM Wish I saw this last week. Notice any difference in throttle response?Very surprised to say it does make a noticable difference in throttle response. I didn't fit it for this reason so added bonus. Might have been a one off, but I smacked the limiter in performance mode which it has never done before. It was like the revs were too quick for the auto, lol. Get one - awesome product. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now