Jarod85 Member 58 Member For: 14y 8m 13d Gender: Male Location: Orange Posted 22/12/10 04:56 AM Share Posted 22/12/10 04:56 AM Hi Guys,My ute has been through a fair bit of crap lately. Been off the road for maybe as long as 8 months. Put a 06/06 motor in it. Backyard job. Was driving fine, sounded good. Felt good. Wasnt rev'ing it past 3 grand at all. Wanna get it a custom tune before I give it a hiding.Today first day on road, only just got it registered. So this was the longest its been driven in months, only a 20 minute drive at that. (short drives to and from blue slipper etc before this).Was reversing in the drive way, it stalled. And wont kick over. Motor will half attempt to crank, the crank pulley maybe turns a third rotation.Its a new battery, and ruled that out with a jump start. same result.One thing in my mind, due to cooking the old motor im pretty paranoid about the temps. When I was driving it, if I stopped at some lights, I would notice the needle would move higher, once car was moving, it would quickly drop. Maybe only 1.5 mm of movement at most. Temp didnt go over half way. Pretty devestated, I had planned on driving it non stop all day :(I have a small suspicion that once it cools down completely, it'll crank. Will give that a go in a few hours.Any thoughts would be great. Link to comment Share on other sites More sharing options...
Rusty XR6T Donating Members 516 Member For: 14y 10m 2d Gender: Male Posted 22/12/10 05:08 AM Share Posted 22/12/10 05:08 AM weird that it just stopped out of nowhere, needle below half should be fine!have you plugged an OBD in and check for error codes? perhaps a connector came loose Link to comment Share on other sites More sharing options...
Jarod85 Member 58 Member For: 14y 8m 13d Gender: Male Location: Orange Posted 22/12/10 05:25 AM Author Share Posted 22/12/10 05:25 AM I havent checked for error codes yet. Good idea though. Link to comment Share on other sites More sharing options...
Adam Here since the start... Lifetime Members 10,282 Member For: 21y 9m 7d Gender: Male Location: Victoria Posted 22/12/10 05:26 AM Share Posted 22/12/10 05:26 AM Has your PCM been flashed to suit the new motor? There would be a calibration difference between a BA and BF motor. Link to comment Share on other sites More sharing options...
Jarod85 Member 58 Member For: 14y 8m 13d Gender: Male Location: Orange Posted 22/12/10 05:59 AM Author Share Posted 22/12/10 05:59 AM Havent changed a thing to the tune between motors. I really didnt think it would be needed between a BA - BF. Even worse news, I cannot find my X3 anywhere. I have an obd scanner that will work with my iphone for codes. Link to comment Share on other sites More sharing options...
seduced Need more power. Now taking donations. Member 753 Member For: 15y 11m 6d Gender: Male Posted 22/12/10 06:06 AM Share Posted 22/12/10 06:06 AM I may be wrong, but I didn't think a BF engine could run on a BA ECU.... Link to comment Share on other sites More sharing options...
Adam Here since the start... Lifetime Members 10,282 Member For: 21y 9m 7d Gender: Male Location: Victoria Posted 22/12/10 06:15 AM Share Posted 22/12/10 06:15 AM The BF has different cam control.There's probably other differences too. Link to comment Share on other sites More sharing options...
icer Banned 2,335 Member For: 15y 6m 16d Gender: Male Location: Aspendale, Vic. Posted 22/12/10 06:25 AM Share Posted 22/12/10 06:25 AM I have an 06/06 motor with a BA 4spd and BA loom/ecu etc with my x3. Link to comment Share on other sites More sharing options...
Jarod85 Member 58 Member For: 14y 8m 13d Gender: Male Location: Orange Posted 22/12/10 06:32 AM Author Share Posted 22/12/10 06:32 AM (edited) So that rules out the ba / bf thing.edit: Did you have the tune changed with the X3 aftewards ? Edited 22/12/10 09:41 AM by RHR No need to quote above post. USE FAST REPLY Link to comment Share on other sites More sharing options...
seduced Need more power. Now taking donations. Member 753 Member For: 15y 11m 6d Gender: Male Posted 22/12/10 06:36 AM Share Posted 22/12/10 06:36 AM Yes but do you have BF heads on yours *Beep*? I am assuming based on op's "cooked the last engine" comment that he has the BF long motor which would include the new cam gear that a BA ecu wouldnt drive correctly. Just throwing theories out there...Sounds like it needs a decent tuner to take a look.. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now