Redback Banned 236 Member For: 15y 8m 17d Gender: Male Location: Blacktown NSW Posted 06/11/10 05:18 AM Share Posted 06/11/10 05:18 AM you need to cut the wires and extent them. I have the same kit. My plazmaman cooler piping has a place I put my boost sensor on the piping just before the cooler core on the passanger side. I reran the cables to reach over there. Cheeck your cooler pipes as there should be a place to put the sensor.What are you guys talking about? If I'm not mistaken this guy said he has a 4" intake and battery relocation kit?????? WTF has the air intake to the turbo and the battery relocation got to do with the boost pressure sensor fitted on the UBP going to the factory cooler?????????Mika are you also fitting an intercooler kit as well or do you have the factory cooler? Link to comment Share on other sites More sharing options...
MiKa Donating Members 4,243 Member For: 18y 6m 8d Gender: Male Location: Melbourne, VIC Posted 06/11/10 06:00 AM Share Posted 06/11/10 06:00 AM Yea sorry, also a nizzy coolerWhere do I fit the sensor to, Cold side pipes or Hotside? Is it ok to drive around as is? *Beep*, the cooler is from there stage 2 kit, which is meant to have a plenum.. I dont have a plenum so I got cold side pipes off plazmaman that runs from the rubber nizpro pipe that goes under the headlight to the TB.. The plazma pipes had a bit welded on but that was for a bov, which I had welded shut..Everything is sorted except for the boost sensor thingy... I cant give it any beans anyway cause its needed a retune before the new bits went on today.. Link to comment Share on other sites More sharing options...
Redback Banned 236 Member For: 15y 8m 17d Gender: Male Location: Blacktown NSW Posted 06/11/10 07:25 AM Share Posted 06/11/10 07:25 AM Well the Nizpro kit has the boost sensor attached to the throttle body reducer pipe that is used for their plenum as in their diagram in the instructions. The plazmaman kit has the boost sensor mounted on the cold side pipe that goes from the outlet of the intercooler to the silicon connector that goes under the headlight. If you do not have this you need to have a boost sensor boss welded in somewhere in your pipes. Link to comment Share on other sites More sharing options...
MiKa Donating Members 4,243 Member For: 18y 6m 8d Gender: Male Location: Melbourne, VIC Posted 06/11/10 08:04 AM Share Posted 06/11/10 08:04 AM So its ok to bo on the cold side? I might send it back to plazmaman and get them to do it... Link to comment Share on other sites More sharing options...
MiKa Donating Members 4,243 Member For: 18y 6m 8d Gender: Male Location: Melbourne, VIC Posted 06/11/10 08:04 AM Share Posted 06/11/10 08:04 AM Ok to drive with it not connected? Link to comment Share on other sites More sharing options...
ebxmple Member 1,322 Member For: 17y 29d Posted 07/11/10 08:56 AM Share Posted 07/11/10 08:56 AM When you have the Nizzy cooler kit without plenum they give you a little alloy block that mounts where the old ubp was and the boost sensor fits into it. A vac line then runs off the block to the cold side pipe to pick up pressure. Link to comment Share on other sites More sharing options...
BOZZTURBO Donating Members 237 Member For: 18y 7m Gender: Male Location: Melbourne Posted 07/11/10 09:23 AM Share Posted 07/11/10 09:23 AM that's what I need , were can I get one from . Link to comment Share on other sites More sharing options...
ebxmple Member 1,322 Member For: 17y 29d Posted 08/11/10 09:00 AM Share Posted 08/11/10 09:00 AM Nizpro might be able to help you as I am sure quite a few upgrade from stg1 to stg2,so they might have a spare laying round. I might have my old one in the shed so if I remember I will have a look. Link to comment Share on other sites More sharing options...
MiKa Donating Members 4,243 Member For: 18y 6m 8d Gender: Male Location: Melbourne, VIC Posted 08/11/10 09:57 AM Share Posted 08/11/10 09:57 AM Shotgun if you do.. Link to comment Share on other sites More sharing options...
BOZZTURBO Donating Members 237 Member For: 18y 7m Gender: Male Location: Melbourne Posted 08/11/10 11:09 AM Share Posted 08/11/10 11:09 AM Nizpro might be able to help you as I am sure quite a few upgrade from stg1 to stg2,so they might have a spare laying round. I might have my old one in the shed so if I remember I will have a look.thanks ebxmple Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now