Panda Eyes flame magnet Gold Donating Members 5,674 Member For: 16y 5m 24d Gender: Male Location: adelaide hills- 'race air' central Posted 20/06/10 12:31 PM Share Posted 20/06/10 12:31 PM I have xenon lights in low and hi beams, and am thinking about putting another set in the fog lights. :o I live in the hills and do alot of driving through the forest etc.I'd like to hook them up to my normal high beam switch. will the circuit take it or should I leave it on the fog light switch (not too convenient though).cheersscott Link to comment Share on other sites More sharing options...
tab Sucker Moderating Team 32,303 Member For: 20y 6m 15d Gender: Male Location: Brisbane Posted 21/06/10 12:56 AM Share Posted 21/06/10 12:56 AM I assume the foglights would be powered by a relay tapped off the parking light circuit...so if you could just swap that over to the high beam circuit you'd be laughing. Assume the relays are in the engine bay fusebox so shouldn't be too much trouble. Link to comment Share on other sites More sharing options...
NYT-SKY Member 155 Member For: 15y 10m 12d Gender: Male Location: SW Sydney Posted 27/06/10 07:59 AM Share Posted 27/06/10 07:59 AM Get a H3 or an even smaller H3C kit and start from there. Might have to lengthen the cables if want to put the ballasts in the engine bay or find a safe spot in the front bar somewhere. Link to comment Share on other sites More sharing options...
Panda Eyes flame magnet Gold Donating Members 5,674 Member For: 16y 5m 24d Gender: Male Location: adelaide hills- 'race air' central Posted 27/06/10 11:40 AM Author Share Posted 27/06/10 11:40 AM yeah true. what is an h3c kit? neveer heard of it Link to comment Share on other sites More sharing options...
foxtrot Member 77 Member For: 16y 1m Posted 27/06/10 11:59 PM Share Posted 27/06/10 11:59 PM Hi. H3 and H3c kits will be the same, the biggest problem is holding the lamp into the reflector as the clip that goes over the back of the normal H3 globe wont fit over a HID globe, What you need to do is drill two small holes in the lip around the edge of the globe holder on the reflector and hold the new globe in with 2 self tappers. Cheers MD Link to comment Share on other sites More sharing options...
NYT-SKY Member 155 Member For: 15y 10m 12d Gender: Male Location: SW Sydney Posted 01/07/10 10:28 PM Share Posted 01/07/10 10:28 PM H3C bulb is much shorter than a H3 bulb. Link to comment Share on other sites More sharing options...
4DZILR Donating Members 713 Member For: 14y 9m 4d Gender: Male Location: Sydney - Brighton Le Sands Posted 02/07/10 04:37 AM Share Posted 02/07/10 04:37 AM is this for the xr6 foggies?yeah it will fit. did it myself.. had them on the xr6 lights. The inside protective cover to reflect the light just needs to be pushed in a little.. then you will need a rubber washer to elevate the globe out of the fog light housing. then all I used was a paper clip to and welded it to the original bezels and twisted it around the head of the globe.now I have them in my f6 lights as I have changed my bar. had to drill the globe cover but used the original grommet you get with the hid kits to seal the whole. turned out awesome! its a lot of work but take your time and youll figure it out Link to comment Share on other sites More sharing options...
Panda Eyes flame magnet Gold Donating Members 5,674 Member For: 16y 5m 24d Gender: Male Location: adelaide hills- 'race air' central Posted 04/09/10 07:24 PM Author Share Posted 04/09/10 07:24 PM cheers zilr... got any pics? Link to comment Share on other sites More sharing options...
sten Member 45 Member For: 14y 5m 1d Posted 14/09/10 08:45 AM Share Posted 14/09/10 08:45 AM Where is the best place to get these kits from? online? Link to comment Share on other sites More sharing options...
Panda Eyes flame magnet Gold Donating Members 5,674 Member For: 16y 5m 24d Gender: Male Location: adelaide hills- 'race air' central Posted 14/09/10 10:32 AM Author Share Posted 14/09/10 10:32 AM ive got a kit coming- gonna be a bit of mucking around to get them to fit. h3c kit.ebay ftw! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now