Jump to content

Treating My F6 To Some Love


Moose

Recommended Posts

  • Member
  • Member For: 16y 8m 18d
  • Gender: Male
  • Location: Ipswich, QLD

Hey crew!

Just dropped the F6 off this morning and am already eager to get her back. I finally sold my 4x4 so thanks to that I can finally do the much need maintenance and upgrades to my beloved Typhoon. Here's the list so far:

Brakes:

DBA 4000 Cross drilled and slotted rotors front and back

"Race Brakes" Pads front and back (from Race Brakes in Sydney, meant to be a really good pad)

Suspension:

Munroe GT Gas Lowered Shocks front and back

King Springs SSL's for the rear (raising it up from my 2" compressed SSL's)

Performance:

4" dump, 4" cat and 4" cat back system all in stainless with mandrel bends.

42lb injectors

Bigger fuel pump

Flash tune for 12psi plus the other adjustments

Also getting my stocko's back, and putting some new rubber on those, including 255/35 semi-slicks. Mainly for the looks, not so much that I have traction issues just yet.

Then a few other little things like its getting a service, few bushes underneath replaced and I believe I've got a f*cked engine/gearbox/diff mount, so hopefully I can get that under warranty.

Also wanted to ask what people expect I'd get from those small performance upgrades?

Will have photos buy the end of the week :D

Link to comment
Share on other sites

  • You are a dead set goose
  • Silver Donating Members
  • Member For: 19y 1m 5d
  • Gender: Male
  • Location: Melbourne

Get the 27mm adjustable Whiteline sway bar for the front. You'll be amazed at the difference it makes and it's a relatively cheap mod. What cooler has it got? That'll effect the power output :innocent:

Link to comment
Share on other sites

  • KILL,KILL,KILL,DIE,DIE,DIE,
  • Member
  • Member For: 18y 8m
  • Gender: Male

Nice you will need those semi slicks as when its finished traction WILL be an issue :spoton:

those mods on an f6 350 + if you have good cooler., but you want get that on 12 psi without plenum etc.

Edited by YPURV4
Link to comment
Share on other sites

  • Member
  • Member For: 16y 8m 18d
  • Gender: Male
  • Location: Ipswich, QLD

I've just got the Monza upgraded cooler at the moment.

Next on the list is waste gate modification, plenum, PWR cooler, pipe work and some other goodies.

Link to comment
Share on other sites

  • KILL,KILL,KILL,DIE,DIE,DIE,
  • Member
  • Member For: 18y 8m
  • Gender: Male

The monza will rob you of power over the 300 mark, to much heat soak at that level trust been there done that, I think you should get one of rapids kits mate very well priced and wil help out alot with power and will be better in th elong run.

Link to comment
Share on other sites

  • Donating Members
  • Member For: 16y 7m 13d
  • Gender: Male
  • Location: north QLD

sounds nice bet you will be happy with them modds.. with them performance around 310-320rwks my phoon made 309 with the same modds but as each car is different u might get more lol.. :eyebrows:

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
  • Create New...
'