RegSpec Cruise Control 1,417 Member For: 17y 10m 24d Gender: Male Location: Macksville NSW. Posted 10/03/09 09:34 AM Share Posted 10/03/09 09:34 AM (edited) I scored a set F6 gauges for my car, and have to drill and tap a port for the boost sensor. Then, I checked the oil press. sensor and it looks like the same thread...... Does anybody know what thread they are?.....I thought they were 1/8 NPT but tried a plug to fit and no-go Edited 10/03/09 09:39 AM by BionicXR6T Link to comment Share on other sites More sharing options...
nifty Lost Member Donating Members 134 Member For: 16y 3m 16d Gender: Male Location: Perth Posted 10/03/09 10:24 AM Share Posted 10/03/09 10:24 AM I fitted mine on the weekend and the thread on the oil pressure sensor is 1/4 x 18 NPT. Male thread on the sensor and female in the hex adaptor to the block. The Male threads on the turbo oil screen hex fitting are 1/4 x 18 NPT on one end and M14 x 1.5p on the other end. Obviously the NPT goes into the block and the M14 goes into the hex adaptor which goes to the oil pressure sender unit. I put an extension between the hex adaptor and the oil pressure sender to tee off for my new gauge sender which has a 1/8 x 27 NPT male thread on the sender unit. Hope I didn't get too wordy and hope this helps. All the best with it. cheers. Link to comment Share on other sites More sharing options...
RegSpec Cruise Control 1,417 Member For: 17y 10m 24d Gender: Male Location: Macksville NSW. Posted 10/03/09 12:58 PM Author Share Posted 10/03/09 12:58 PM ....thanks nifty. Link to comment Share on other sites More sharing options...
jasol Member 571 Member For: 15y 9m 24d Location: adelaide Posted 29/04/09 09:19 PM Share Posted 29/04/09 09:19 PM I fitted mine on the weekend and the thread on the oil pressure sensor is 1/4 x 18 NPT. Male thread on the sensor and female in the hex adaptor to the block. The Male threads on the turbo oil screen hex fitting are 1/4 x 18 NPT on one end and M14 x 1.5p on the other end. Obviously the NPT goes into the block and the M14 goes into the hex adaptor which goes to the oil pressure sender unit. I put an extension between the hex adaptor and the oil pressure sender to tee off for my new gauge sender which has a 1/8 x 27 NPT male thread on the sender unit. Hope I didn't get too wordy and hope this helps. All the best with it. cheers.when you fitted it did you need to drain the oil? Link to comment Share on other sites More sharing options...
nifty Lost Member Donating Members 134 Member For: 16y 3m 16d Gender: Male Location: Perth Posted 30/04/09 09:36 AM Share Posted 30/04/09 09:36 AM no, but had to remove oil filter for better access. Link to comment Share on other sites More sharing options...
XRPete Member 673 Member For: 17y 2m 11d Gender: Male Location: Here Posted 09/11/09 09:52 AM Share Posted 09/11/09 09:52 AM Hey guys hope someone can help me here. I just replaced the oil sensor on the sandwhich plate(for my guages) because it was melted. There was no thread tape on the old one so I didn't put any on the new one. Now its leaking a bit of oil. Is there a special type of thread tape or sealant that I use?Many Thanks Pete Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now