tinyplums Member 1,080 Member For: 16y 4m 19d Gender: Male Posted 21/05/10 07:23 AM Share Posted 21/05/10 07:23 AM what your obviously not familar with is that tocchi is like a magpie, atracted to shiny things. there may be an advantage, but would come second to the fact its shiny. Link to comment Share on other sites More sharing options...
Tocchi Sandtrap Motorsport Donating Members 2,055 Member For: 16y 29d Gender: Male Location: Perth Posted 21/05/10 07:59 AM Author Share Posted 21/05/10 07:59 AM ^^ WIN !!!yeh it would shield the intake manifold from "engine bay" heat. Link to comment Share on other sites More sharing options...
Tocchi Sandtrap Motorsport Donating Members 2,055 Member For: 16y 29d Gender: Male Location: Perth Posted 21/05/10 08:06 AM Author Share Posted 21/05/10 08:06 AM sneak peak photo. dont want to give away too much yetits a depressing 4.5" dump pipe there.1.5" pipes on the manifold.T51the wastegate port has to be done on the rear housing in the photo, was done at the base due to it being a twin scroll turbo Link to comment Share on other sites More sharing options...
Worm A much better forum Silver Donating Members 3,808 Member For: 16y 5m 1d Gender: Male Location: Victoria Posted 21/05/10 08:16 AM Share Posted 21/05/10 08:16 AM I am farking hanging to see this thing run matty... Link to comment Share on other sites More sharing options...
Tocchi Sandtrap Motorsport Donating Members 2,055 Member For: 16y 29d Gender: Male Location: Perth Posted 21/05/10 08:20 AM Author Share Posted 21/05/10 08:20 AM yeh same just trying to get a hold of the workshop (late friday arvo -- good luck ) to find out what hose I need for the oil supply line.factory oil supply came off the sender aye?either Dash-4 or Dash-6? Link to comment Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,323 Member For: 19y 3m Gender: Male Location: Perth Posted 21/05/10 08:45 AM Share Posted 21/05/10 08:45 AM factory was dash 3.5 (5MMISH ID) you want -4. Are you keeping the pressure switch in that location? cant tell you what size banjo you need if you are.... Link to comment Share on other sites More sharing options...
Tocchi Sandtrap Motorsport Donating Members 2,055 Member For: 16y 29d Gender: Male Location: Perth Posted 21/05/10 08:49 AM Author Share Posted 21/05/10 08:49 AM nah im running mechanical gauge, so it will be a T-piece into the block (where switch/sender goes). one line goes to gauge, the other to turbo.unless theres something wrong with doing it that way? Link to comment Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,323 Member For: 19y 3m Gender: Male Location: Perth Posted 21/05/10 09:10 AM Share Posted 21/05/10 09:10 AM nope no problem at all. As long as any turbo oil pressure inlet restrictor orifices are in place on the turbo (if required) Link to comment Share on other sites More sharing options...
Guest EGOXRT Guests Posted 21/05/10 11:57 AM Share Posted 21/05/10 11:57 AM 14mm banjo Link to comment Share on other sites More sharing options...
Tocchi Sandtrap Motorsport Donating Members 2,055 Member For: 16y 29d Gender: Male Location: Perth Posted 24/05/10 03:56 AM Author Share Posted 24/05/10 03:56 AM to think I was worried about my chassis holding up to the power of the 6T.thinking the only motor its has was the 650flyHP clevo 383 N/Aturns out the previous owner had a supercharged small block and it ran 7s.. fills me with more confidence with the car theres not much to do now:buy tyres for tuning (MT sportsman or something)buy Motec MSDL dash -- not needed at the moment, one of those "in the future" purchasesmake up pipe for throttle bodymake the wastegate port still has to be done (I think), then make the screamer pipe (easy)intall the Atomic Ovate styled valve springsoil lines for turbowire up motec, and tune.unless im missing something obvious, then theres not much to do.unsure what im going to do with panel & paint now, as my painter (BBK) has stopped painting and started selling paint as a supplier.eeeeep :( Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now