Chipa Member 6 Member For: 17y 5m 10d Location: Albury, NSW Posted 13/10/08 11:34 AM Share Posted 13/10/08 11:34 AM I really need to troll through here more often... Love the look of the project. Mr Bean & innovation, everything we've come to expect of you. Keep up the good work! Link to comment Share on other sites More sharing options...
MiKa Donating Members 4,243 Member For: 18y 2m 25d Gender: Male Location: Melbourne, VIC Posted 28/10/08 10:19 AM Share Posted 28/10/08 10:19 AM Any updates??? Link to comment Share on other sites More sharing options...
SubJimbo ŠύЂפֿĺmβø ™ Donating Members 1,216 Member For: 16y 10m 14d Gender: Male Location: Melbourne Posted 08/11/08 11:41 AM Share Posted 08/11/08 11:41 AM , Hows it going Beanie? Link to comment Share on other sites More sharing options...
glimmerman Member 90 Member For: 16y 3m 2d Gender: Male Location: Penrith, NSW, OZtralia Posted 12/11/08 12:07 PM Share Posted 12/11/08 12:07 PM I think there may be a few snags to run into... These ICC's, can be diagnosed apparently, just like your car. A mechanic can plug it in, and tell you whats going on with your ICC. Also the central locking, indicators, brake lights, all interior circuit controls such as door locks, interior lamps, and my assumption also air bags, driver seat positions, all run off the ICC... because if you put LED bulbs in the indicators which run on the same CAN as the air bag apparently... I would assume since indicators run through the ICC so too would the air bags. I was going to do what a few have managed successfully by integrating a dvd player in the middle of the ICC and make it a bit longer to accomodate moving circuit boards around, my mechanic who owns a BA also urged me to just install it underneath because its too risky with how much just runs through this.You may already be aware of all these things...Steve Link to comment Share on other sites More sharing options...
Cashie Donating Members 663 Member For: 21y 9m 19d Gender: Male Location: Perth Posted 30/11/08 12:42 AM Share Posted 30/11/08 12:42 AM any updates at all guys? Link to comment Share on other sites More sharing options...
ottafish Member 14 Member For: 17y 4m 29d Posted 07/12/08 12:05 PM Share Posted 07/12/08 12:05 PM I've just been reading through this thread. Awsome... Been reading through the Palmer Performance site and keen to get the Dashcommand softeware running on this project. Thanks everyone... Link to comment Share on other sites More sharing options...
foggy Inactive Members 1 Member For: 17y 4m 18d Posted 06/01/09 08:45 PM Share Posted 06/01/09 08:45 PM Hi Mr Bean,Any updates on this project???? Link to comment Share on other sites More sharing options...
Tree Monkey Member 685 Member For: 16y 11m 6d Gender: Male Location: brisvagas / Manly Posted 02/03/09 11:43 AM Share Posted 02/03/09 11:43 AM UPDATE>>>>>>>>> I sent a icc for this project and nothing yet???????????? Link to comment Share on other sites More sharing options...
SubJimbo ŠύЂפֿĺmβø ™ Donating Members 1,216 Member For: 16y 10m 14d Gender: Male Location: Melbourne Posted 02/03/09 01:12 PM Share Posted 02/03/09 01:12 PM Hopefully Beanie reads this.. His been on the forums contacting Fadi about an FG ICC, Hope he sees this, mayeb you want to drop him a PM? Link to comment Share on other sites More sharing options...
MrBean Member 400 Member For: 18y 6m 9d Location: Melbourne Posted 03/03/09 10:39 AM Author Share Posted 03/03/09 10:39 AM (edited) UPDATE>>>>>>>>> I sent a icc for this project and nothing yet????????????AndCertainly, if you donate something like a ICC, I will definately remember you - but, please be aware projects like these can take significant time to mature, as I have a few hours here and there to work on it, due to work committments....Otherwise, I can always look at getting an ICC back to you again if this doesn't work out.Hello Tree Monkey, as I mentioned a few posts back, reverse-engineering takes quite a fair bit of time, and if you're more comfortable having your ICC back, I will kindly ship it, as mentioned previously. I have had limited time available this last couple months due to ever-increasing pressure from our mother-company in Finland, and have been travelling more than I've at home :(So yes, I do realize progress is slow, but at least there's some.UpdateI have the Commell LV-372 3.5" up and running, 100% complete, with Centrafuse 2.1 frontend. Very recently installed an OCZ Apex 60gig SSD, and am happy to report boot times, from power switch to desktop in 22 seconds. Very quick if you ask me.I received the newly designed TPMS interface from Alok on PortalMediaPC, and have it configured, and up and running. Designed my own 1/4-wave whip antenna for the sucker, and it works very well, tyre-pressures and temps updating to the frontend...I have stripped my old manual ICC to get the housing sorted to fit the Commell board, currently busy with that. As mentioned earlier, one of the goals is to reuse existing infrastructure, and mount everything so as to look factory standard. Good progress here, and hoping finally to have the pics up on the weekend.The SSD held me back here, as I ultimately wanted to use one vs the 7200 Momentus harddrive, and I'm glad I waited for it to become affordable before purchasing. Now, at least the carputer part is complete.I'm having fun to fit the new transflective LCD (8.4" sun-readable industrial) in the std ICC fascia, the problem is the engineering plastic used in injection molding these things, PPO/PPE - nothing really bonds to it, so you cannot glue/weld it like ABS derivatives. Damn. I would not like to use fiberglass/fillers etc.Anyway....Onto the AVR CAN controller:I have been busy reverse-engineering the original factory LCD - the TFT unit with nice color graphics overlays - I want to integrate this into the new transflective LCD controller, an ALR-1400 from Digital View, which has some form of overlay control on the onboard Genesis controller chip.By doing this, I want to retain all existing functionality on 1 LCD, instead of having 2.....would make for a much cleaner solution.I am also finalizing the daughterboard PCB that will fit between the existing ICC pushbuttons, and mount directly to the CAN-AVR - then off to the PCB manufacturers to make a prototype or 2.So, apologies if progress seems slow, guys - I will try and spend more time on this, and get something positive out soon - I'm burning for us to start on the microcode, and have mostly all the PIDs available to start with porgramming and testing.I have a small sample programming running in the AVR, pulsing an LED on/off at faster or slower rates, depending on a pushbutton selection, so it's working fine.Do anyone here have some contacts that can get me the schematic on the factory TFT LCD controller board - it seems Sumitomo made this for Ford, and I'm hoping to find the schematic from some insiders.....Will make my job a lot easier.If you want to remain anonymous, please PM me, I will keep it highly confidential.Kind regards,Beanie Edited 03/03/09 10:42 AM by MrBean Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now