senna_T Forged Member Lifetime Members 15,818 Member For: 17y 9m 1d Gender: Male Location: SW Sydney Posted 02/03/08 04:08 AM Share Posted 02/03/08 04:08 AM the drif6 was just the normal plenum with the throttle body turned around, so I'm sure it was a simple conclusion Link to comment Share on other sites More sharing options...
JP300 Donating Members 842 Member For: 19y 1m 26d Gender: Male Location: Sydney Posted 02/03/08 04:11 AM Share Posted 02/03/08 04:11 AM So Pat, when are the XR6Ts and the F6 cars going to be available in the showroom? Link to comment Share on other sites More sharing options...
senna_T Forged Member Lifetime Members 15,818 Member For: 17y 9m 1d Gender: Male Location: SW Sydney Posted 02/03/08 04:16 AM Share Posted 02/03/08 04:16 AM we should see them up here in may, hopefully we might be lucky and get them at the end of april. I might start a poll to see if people would be interested coming to a launch night at the dealership - I'm not sure if this breaches any rules for the forum though... Link to comment Share on other sites More sharing options...
2MUCHKW Member 350 Member For: 18y 6m 20d Posted 02/03/08 04:34 AM Share Posted 02/03/08 04:34 AM Wheres the throttle body ... is it vertically mounted under the air intake plumbing?Great pics ... thx bloke Link to comment Share on other sites More sharing options...
Full Monty Member 513 Member For: 17y 4m 16d Gender: Male Location: Melbourne Posted 02/03/08 06:56 AM Author Share Posted 02/03/08 06:56 AM (edited) Throttle body is in the middle of the new intake plenum on the top, The cold pipe from the cooler routes directly to it, and bends 90 degree downward into the throttle body.I imagine you could easily buy a BA - BF lower plenum and any current aftermarket plenum will fit.The pipework, both hot and cold side has a clamp join section just before it enters below the headlight on each side, so easy underbonnet removal and replacement with aftermarket, note they have now located the boost sensor right at the throttlebody (after the cooler, rather than before as previously done).also there is an access hole, filled with a large hex bolt in the front end of the plenum chamber, not sure what this is for? Edited 02/03/08 02:41 PM by Dagabond Link to comment Share on other sites More sharing options...
XR06T Silver Donating Members 4,146 Member For: 19y 4m 17d Gender: Male Posted 02/03/08 07:08 AM Share Posted 02/03/08 07:08 AM thanks heaps for the pics and info mate..so you think the current lower plenum bit will bolt up? that's good news! Link to comment Share on other sites More sharing options...
Venom XR6 Member 1,460 Member For: 21y 6m 13d Location: Geelong Victoria Posted 02/03/08 08:04 AM Share Posted 02/03/08 08:04 AM Old plenums won't fit, the bolt holes have been moved around where the manifold bolts to the head. Link to comment Share on other sites More sharing options...
Venom XR6 Member 1,460 Member For: 21y 6m 13d Location: Geelong Victoria Posted 02/03/08 08:06 AM Share Posted 02/03/08 08:06 AM Wheels look crap on the xr6T, just not suited (XR5 style). I hope they are released with new styling.There are 19 inch 5 spokers optional if you don't like the XR5 style 18's. Link to comment Share on other sites More sharing options...
Evil F6 Donating Members 830 Member For: 18y 9m 30d Gender: Male Location: Sydney Posted 02/03/08 11:01 AM Share Posted 02/03/08 11:01 AM My guess is that these cars are going to be restricted in stock trim as I think that are going to have a smaller turbo and piping with smaller plenum and shorter intake runners it will not produce the same low end torque as the BA-BFs. This could be good news to BA and BF users!!Ah, I think you'll find the complete opposite - they'll make better low down torque than the BA-BF. They might struggle to make big power with the smaller turine wheel though. Link to comment Share on other sites More sharing options...
01txr Member 861 Member For: 17y 9m 25d Gender: Male Location: QLD Posted 02/03/08 01:53 PM Share Posted 02/03/08 01:53 PM Sorry didnt explain in full when I said Plazmaman plenum would be easy to fit up.Should of said with use of BA-BF lower runners as the head seems to have same bolt pattern, may need to alter manifold runners to match the staggered ports though. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now