Stock Dyno, Is This Correct!

[straughsberry]

Comments please… 277rwkw seems a lot for a stock phoon!

I did do a track day recently and was pulling away from a GTS on the straights and kept up with a supercharged R8….

Maybe cheap from China dyno it is?

Read the instructions that came with it and you may find that there is no mention of kilowatt. They may be using the lesser known, and lesser rated "killerwatts".

[7MA61]

For starters torque figures at the wheels mean nothing, its simply tractive effort ie torque at the engine multiplied by the leverage advantage, geabox,length of the driveshaft, diff ratios & tyre size.

As for power that's pretty damn high, but given its not on a dyno dynamics dyno its hard to compare, theres also no indicators of inlet temps which could artificially inflate readings.

Easy way to check find the nearest drag strip, theres a formula using terminal speed and car weight that gives a good indication of RWHP.

[DesFlurane]

Relax guys, he did 13.5 @ 106 at Meremere (a slow track to be sure).

Suggest you go to another dyno, IPV, Torque Performance or Eastern. Also make sure that they log boost and importantly AFRs.

Nice number though.

[hamnzf6]

maybe our ausy friends are pissed cause they send all the good cars over here

yip booked in on monday for another go, (different dyno)

also had Paul at IPV look at the complete dyno run on disk, he said all looked good, had seen simialr numbers on his dyno on a few phoons..

[ratter]

maybe our ausy friends are pissed cause they send all the good cars over here

Dont you guys measure the power as sheep power rather than horsepower or the metric equivalent Killer wasps,

could explaing the high figure :tonguepoke

Edited 28/11/07 03:18 AM by ratter

[bcl]

That is a very high figure for a F6, compared to what we have seen on dd, mainline and dynapack dynos.

Looks like it's about 30-40rwkw higher than normal (in Australia). Must see boost levels, as it could be overboosting..

Are you running with a cat installed?

Ask your tuner to use DIN correction not SAE, and I'd expect to see a lower figure, and something more like I'd expect to see.

Although the diff states 4.1, whereas actually it is 3.73, that will not impact power figures.

Ask your tuner to print the tcf value on the sheet, just to confirm that he is not using a factor other than 1.

Is this an auto or manual?

Brian

[Guest EGOXRT]

"His dyno bolted onto the wheel hubs rather than the rolling road type..."

Don't they read higher than rollers??

[SHOWDOWN]

"His dyno bolted onto the wheel hubs rather than the rolling road type..."

Don't they read higher than rollers??

Only when the wheels loose traction on the rollers.

should be +/- 1-5rwkws on stockers or lightly moded cars..

Ozzie

[hamnzf6]

That is a very high figure for a F6, compared to what we have seen on dd, mainline and dynapack dynos.

Looks like it's about 30-40rwkw higher than normal (in Australia). Must see boost levels, as it could be overboosting..

Are you running with a cat installed?

Ask your tuner to use DIN correction not SAE, and I'd expect to see a lower figure, and something more like I'd expect to see.

Although the diff states 4.1, whereas actually it is 3.73, that will not impact power figures.

Ask your tuner to print the tcf value on the sheet, just to confirm that he is not using a factor other than 1.

Is this an auto or manual?

Brian

Its booked in for another run on monday so will pass all this on and report back. (its an auto)

[DesFlurane]

I'm guessing 243rwKw.