XF Falcon <put funny sh*t here> Member 3,365 Member For: 18y 21d Gender: Male Location: Perth, NOR Posted 06/07/14 04:48 PM Share Posted 06/07/14 04:48 PM Clever fish you got there mate! :D 1 Link to comment Share on other sites More sharing options...
genuine honest person Member 2,769 Member For: 10y 10m 1d Gender: Male Location: near brisbane Posted 06/07/14 09:47 PM Share Posted 06/07/14 09:47 PM I was lucky I did it while the engine was out (ba ) .jake a mate of mine did his fg in about 4 hours .remove air box piping etc Link to comment Share on other sites More sharing options...
discostig Manual mode ________________________ All day, erryday Donating Members 13,798 Member For: 17y 5d Gender: Male Location: Probably above atmospheric pressure Posted 07/07/14 06:47 AM Share Posted 07/07/14 06:47 AM There must be a thread around here on it by now, surely. I got assistance at a forum DIY day for mine and it's hazy. Link to comment Share on other sites More sharing options...
Steven87 Member 109 Member For: 12y 11m 25d Gender: Male Location: Westside Posted 07/07/14 07:57 AM Share Posted 07/07/14 07:57 AM I just removed the air box and get a deep socket 24 mm and extension and it's easy as. Done mine in 20mins Just dnt over tight it and get new copper orings from ford $10 pair. Link to comment Share on other sites More sharing options...
masda74 To Loud Gold Donating Members 4,112 Member For: 12y 11m 30d Gender: Male Location: WA, Perth Posted 07/07/14 07:57 AM Share Posted 07/07/14 07:57 AM There is a write up on the AFF forum. I am not sure if there is one on our forum though. Link to comment Share on other sites More sharing options...
hawlass Silver Donating Members 1,161 Member For: 17y 21d Gender: Male Location: left right out Posted 07/07/14 08:05 AM Share Posted 07/07/14 08:05 AM The AFF thread was the one I used, very good read.http://www.fordforums.com.au/showthread.php?t=73561 Link to comment Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,323 Member For: 19y 2m 6d Gender: Male Location: Perth Posted 07/07/14 08:13 AM Author Share Posted 07/07/14 08:13 AM LOL the aff tutorial is the one I wrote. Which can be found at the start of this thread.... 4 Link to comment Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,323 Member For: 19y 2m 6d Gender: Male Location: Perth Posted 07/07/14 08:22 AM Author Share Posted 07/07/14 08:22 AM Hey guys the new engine in my car has done almost 10000k's now so i decided i would be a good time to remove the oil supply screen and inspect and clean it. I wanted to ensure there was no metal or debris in it from the running in period and with Ninka helpful expertise removed, cleaned and refitted the screen. I took as many photos as i could but its very difficult to get a decent shot of the assembly on the car. With the recent run of turbo failures i thought a how guide might be helpful.Heres a basic how to guide...Step 1: Find the Damn thing:Jack the car up and place it on good jack stands.The Turbo oil supply fitting is located on the left side of the engine block directly above the LHS engine mount. The easiest access is from under the car up and over the engine cross member near the starter motor.attachmentStep 2: removing the fittings:1st you need to remove the oil pressure switch wiring. Then you need to remove the adapter fitting for the oil pressure switch to remove the pipe from the screen. To do this you need a 24mm spanner to remove the adapter fitting and another 24mm to hold the screen fitting that screws in to the block. Its VERY VERY important that you hold the screen fitting in the block to prevent it from rotating and kinking the oil supply pipe as you try to remove it. If you remove the oil pressure switch first (22mm socket or spanner, once again make sure you hold the filter screen) you can use a socket to remove the adapter.attachmentStep 3: Remove the Screen: Not quite as easy as it sounds....If you car has an FPV oil cooler fitted and has a ZF6 speed trans this step is going to make you cry.. The access is very tight. Remove the screen from the engine block with a 24mm spanner.step 4: cleaning the screen: I used CRC contact cleaner but any spray solvent will do.(ie carby cleaner) Spray through the hole back into the fitting. This is the opposite direction to the normal oil flow and will flush the screen. Once you have flushed the screen spray any debris from inside the fitting with the solvent. Use a wire brush to remove any old sealant from the screen and oil pressure switch. Use your solvent to clean out the adapter fitting.attachmentStep 5: Sealing washers: The washer are available from Ford (part number: E8321495300) They all come from Ford with marks in the sealing surface from when they are manufactured.(Ninka Tip #1) To ensure the best seal its advisable to remove these marks. The best way to do this is with a piece of Wet and Dry sand paper on a flat piece of wood or glass. A smooth piece of concrete also work well (thats what i did... ).Annealing the copper to soften it will also enhance sealingattachmentThey should be more like this.....the smoother the better you want to get ride of any deep grooves. The very light surface marks don't matter.Step 6: Reassembly: The Screen fitting has a circlip groove cut into the inside of it for the screen retaining circlip. The fitting is EXTREMELY THIN . in this area if you try to over tighten the adapter fitting onto the screen YOU WILL BREAK THE SCREEN the scrren fittings are $70 a pop from your local Fraud service center.attachment(sorry for the p*ss poor photo but it was very hard to photograph)To ensure you don't need to over tighten it use the best hydraulic sealant you can find. I use Loctite PST 561 in a stick. Its designed for much higher pressures than a lube system could ever dream of making. Make sure you clean any oil from the fitting with your solvent. Refit the fitting to the block and tighten. It doesn't need to be super tight as its a tapered fitting.Step 7: Refitting the oil supply tube: install one of the sealing washers onto the screen fitting. (Ninka tip#2 a small smear of Hydraulic sealant on both sides of the sealing washer this will help ensure a good seal). Refit the oil supply tube. This may take a bit of giggling to get it to slide down past the thread but it will go.Step 8: Install the adapter fitting: Fit a second washer on to the screen with a light smear of sealant on both side and apply sealant to the thread on the end of the screen fitting. Install the adapter onto the screen. Make sure you hold the screen fitting with a 24mm spanner to prevent it turning and kinking the pipe!If you have applied the sealant and cleaned up the washer as described it wont need to be very tight just snug. Be mindful that if you go at it like a gorilla you risk breaking the screen fitting.Step 9: Refit the oil pressure switch. Once again clean up the thread to remove any old sealant. Use your solvent. If the sealant is stubborn you a wire brush to remove it. Apply new sealant to the threads. Refit the switch to the adapter fitting. Use a 24mm spanner to hold the adapter fitting to prevent the whole lot form turning and kinking the pipe. Refit the switch wiringStep 10: The test:Lower the car down and run it until it reaches running temp. Check for leaks...if there no leaks you a champ if there is you phucked up and didn't follow the directions properly.... Please fell free to add to this if i missed anything.... LukeHerp derp Link to comment Share on other sites More sharing options...
hawlass Silver Donating Members 1,161 Member For: 17y 21d Gender: Male Location: left right out Posted 07/07/14 08:50 AM Share Posted 07/07/14 08:50 AM LOL the aff tutorial is the one I wrote. Which can be found at the start of this thread....haha, should have looked there first. Great write up Ralph Link to comment Share on other sites More sharing options...
MattyP MattyP Cruise Control 6,317 Member For: 12y 6m 25d Gender: Male Location: Central Coast Posted 07/07/14 09:02 AM Share Posted 07/07/14 09:02 AM I think we are all a tad red faced right now Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now