stealthxr Donating Members 553 Member For: 18y 10m 8d Gender: Male Location: The Shire Sydney AUS Posted 11/06/06 04:06 PM Share Posted 11/06/06 04:06 PM Just finished installing the next phase of my project A HYBRID COoLER for the T !!! For those intrested I've put together a little guide!!!! ... All Plumbing (Except for headlight tract), silcone hoses, H/D clamps, Backets and minimal cutting (honest) ...P.S.... I/C and Plumbing come in polished alloy, I got my end tanks and plumbing powder coated and the cores and fins are sprayed with GMH black (powder coating restricts air flow) to retain the orignal look!!!!!! (keeps the boys in Blue away) .. Remove front bar, RHS light and factory I/C and plumbing battery and box..Close UpFit the first pipe from the Throttle Body Tract to Headlight tract, P.S lube the inside of the hoses with drop of WD 40 it makes fitting alot easier ( do not tighten any clamps just loose fit )fit the S type pipe to the tubro from underneath and the remaining long piece... other viewRemove The Thermo AssY>>>> 2 10MM Bolt @ the top and slide up & out*****Before you do this inspect shaving points on Thermo fan housing by butting the plumbing up against it before you remove it from the car.. Left thermo shave (pic is a guide).. Right Thermo shave... Got trigger happy with the grinder and cut 30mm to much on the bottom side of the rimm of the housing have a good look b4 you shave and dont touch the fan blades it will stuff its balance up...Here is the only peice of metal that was cut and it dosn't need to be for those not wanting to cut, its gives the silicon hose good clearance when it is cut, Its a stud and nut on a metal plate that protrudes off the lower radiator support....... that supports the A/C hose has no other funtion, rotate the A/C bracket 45* up and remove the screw and replace with nut and bolt and fasten the hose to it... Fit cooler But put top bracket on firstFit last Pipe and hosing..Fit remaining Brackets Trim to correct length ,had to re-drill LHS bracket to match factory mounting point,Screw oil cooler back in against supplied brackets use washer's to space accordingly Tighten all loose bits and HOPE 4 THE BEST..dont forget the HoRN you can put one on either side just cut a longer wire to link themfinal picThanks Lloyd for your help..Took us 8 hours, 4hr work 4hrs drinking and fartarsing around...will 2.5 if there is a next time... Link to comment Share on other sites More sharing options...
CSV_LS1 Member 303 Member For: 20y 9m 13d Gender: Male Posted 11/06/06 05:03 PM Share Posted 11/06/06 05:03 PM Great guide Link to comment Share on other sites More sharing options...
qwigybo Member 288 Member For: 18y 7m 12d Location: bendigo home of SFA Posted 11/06/06 06:22 PM Share Posted 11/06/06 06:22 PM thanks for the guide, nice installation Link to comment Share on other sites More sharing options...
LightningXR6T Member 197 Member For: 19y 5m 14d Location: Newcastle NSW Posted 11/06/06 09:10 PM Share Posted 11/06/06 09:10 PM Great guide, Thanks! Just one question, where did you get it . I have spoken to them and looked at there website, and their quoting $1000 for the kit! Link to comment Share on other sites More sharing options...
stealthxr Donating Members 553 Member For: 18y 10m 8d Gender: Male Location: The Shire Sydney AUS Posted 11/06/06 10:21 PM Author Share Posted 11/06/06 10:21 PM Great guide, Thanks! Just one question, where did you get it. I have spoken to them and looked at there website, and their quoting $1000 for the kit!TRY www.modyourcar.com.auI found it in there.. Link to comment Share on other sites More sharing options...
Fat-Tony Member 5,364 Member For: 18y 8m 24d Posted 12/06/06 01:16 AM Share Posted 12/06/06 01:16 AM looks good in the black, doenst stand out to much. You got any pics of the car reassembled? Link to comment Share on other sites More sharing options...
1axr TEAM BLUEPRINT Member 913 Member For: 21y 10m 10d Location: Perth W.A. Posted 12/06/06 02:34 AM Share Posted 12/06/06 02:34 AM well done. top post. Link to comment Share on other sites More sharing options...
stealthxr Donating Members 553 Member For: 18y 10m 8d Gender: Male Location: The Shire Sydney AUS Posted 12/06/06 04:56 AM Author Share Posted 12/06/06 04:56 AM Here is the pic that shows the cut in radiator supportand the assambled Pic Link to comment Share on other sites More sharing options...
TUFXRT6 Silver Donating Members 687 Member For: 18y 8m 25d Gender: Male Location: Victoria Posted 12/06/06 05:43 AM Share Posted 12/06/06 05:43 AM I have been looking at the Hybrid IC also, do you know how much of a power gain you would get running a Hybrid on a stock XRT compared to e.g. a FPV IC???The pricing is really good & the name behind the product is good so all that's left is the results this thread will be helpful for sure Link to comment Share on other sites More sharing options...
INPURSUIT Fastest Taxi In Melbourne Donating Members 701 Member For: 18y 9m 5d Gender: Male Location: Melbourne Posted 12/06/06 05:51 AM Share Posted 12/06/06 05:51 AM great job mate, very well done Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now