ETM Member 1,194 Member For: 17y 7m 27d Gender: Male Location: syd south Posted 05/05/08 09:45 AM Share Posted 05/05/08 09:45 AM (edited) its pretty easy doc.basically you want the cap wound out as far as possible without the valve opening unnecessarily.to set the spring tension wind the cap outwards a turn at a time,giving the engine a good rev (with the trans in neutral) untill the engine idle speed dips when you back off the throtle, then turn it the other way (tighter) half a turn.road test to make sure it doesnt want to stall,if it does give another half turn tighter. Edited 05/05/08 09:46 AM by ETM Link to comment Share on other sites More sharing options...
dev33 Member 44 Member For: 16y 10m 25d Gender: Male Location: Rockhampton CQ Posted 05/05/08 10:53 AM Share Posted 05/05/08 10:53 AM At the chance of sounding lazy/ignorante but are the kompact BOVs a directswap for the stock ones fitting wise?Or do you have to, like all other BOVs, have to plumb it in with an adaptor? Link to comment Share on other sites More sharing options...
mic Donating Members 1,725 Member For: 16y 9m 22d Gender: Male Posted 05/05/08 11:48 AM Share Posted 05/05/08 11:48 AM Think it will fit straight onto the std cross mate. I have a 38mm megasonic and run 16 psi. It never leaks no matter what I do. Link to comment Share on other sites More sharing options...
hulk xr6t Member 160 Member For: 17y 24d Posted 05/05/08 12:19 PM Share Posted 05/05/08 12:19 PM I have the Kompact series Turbosmart Plumback BOV and it is a direct replacement. No Adaptors needed. (it is the 25mm model).The reason why I bought it, it has a bigger internal valve (still vents through a 25mm opening and I wanted more confidence that the standard BOV isnt leaking any boost. Its also made of metal and Im sure Turbosmart built it pretty well. Sort of like making sure my XR6T eats all its vegetables...BUT..... I checked the instructions and the boost side and the exhaust side of the BOV are opposite to the standard Bosch BOV. I would advise anyone who simply installs it the same way the BOSCH unit works to check which way it vents as it works in the opposite manner.. The Vaccum line fits in it aganst the boost side. (Per attached) Link to comment Share on other sites More sharing options...
dev33 Member 44 Member For: 16y 10m 25d Gender: Male Location: Rockhampton CQ Posted 05/05/08 12:38 PM Share Posted 05/05/08 12:38 PM Sort of like making sure my XR6T eats all its vegetables... that's awesome!!I was looking to replace the standard BOV and being that easyto fit I'm all over it. Who's the best to get one through? Link to comment Share on other sites More sharing options...
hypnodoc It's All In Your Mind Gold Donating Members 2,198 Member For: 21y 11d Gender: Male Location: Melbourne Posted 05/05/08 01:14 PM Share Posted 05/05/08 01:14 PM ETM, a site sponsor has a good deal on them Link to comment Share on other sites More sharing options...
Mr Man Mad Scientist Member 816 Member For: 19y 11m 11d Gender: Male Location: Vic Posted 06/05/08 12:53 AM Share Posted 06/05/08 12:53 AM (edited) I run a turbosmart dual kompact and have the spring wound to hard, when I first had it the spring was set of soft and the valve fluttered to much for my liking.since I have wound the spring up to the hard setting it just sneezes but only at higher boost/rpm. Edited 06/05/08 12:55 AM by Mr Man Link to comment Share on other sites More sharing options...
hulk xr6t Member 160 Member For: 17y 24d Posted 06/05/08 01:17 AM Share Posted 06/05/08 01:17 AM (edited) Sort of like making sure my XR6T eats all its vegetables... that's awesome!!You dont wanna be putting boost in there and the XR6T leaks it out like a kid avoiding eating his peas and chucking them under the table on the floor...Its my understanding though that under boost, soft or hard setting they wont leak boost. that's the reason why I bought it. There is much commentary in other threads/forums about if you leave it too soft it will leak boost.... Is that the same as if you pull a face and the wind changes argument or is it true...In saying that is the stock BOV known to leak boost?? Edited 06/05/08 01:19 AM by hulk xr6t 1 Link to comment Share on other sites More sharing options...
Chich Damn You's A Sexy Chich Member 3,843 Member For: 16y 8m 24d Gender: Male Location: Your House Posted 30/05/08 07:42 AM Share Posted 30/05/08 07:42 AM mine is set as soft as it will allow and it don't leak at all.... Link to comment Share on other sites More sharing options...
mic Donating Members 1,725 Member For: 16y 9m 22d Gender: Male Posted 30/05/08 08:02 AM Share Posted 30/05/08 08:02 AM If your vacuum line is disconnected any bov will leak. The std ones are plastic though so maybe they will leak anyway. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now