Zadz Member 63 Member For: 16y 4m 22d Gender: Male Location: WA Perth Posted 14/02/12 03:22 AM Share Posted 14/02/12 03:22 AM Not to sure yet, need to get it on a dyno again. Just wanna change my coldside IC piping first, could be a problem.Have boost gauge hooked up to it now, so its holding boost alright. Some days it feels good others it doesnt so im still confused.Haven't had the cash to play with it to much, spending it all on doin maintenance. General service, clutch flush, plugs etc. Need to finish gearbox oil change and diff, new rotors, pads and brake fluid flush. Thennnnn I can start spending money on more tuning. Dyno, xcal3 and retune. Link to comment Share on other sites More sharing options...
Slash Donkey Dick Member 801 Member For: 14y 7m 22d Gender: Male Posted 14/02/12 04:13 AM Share Posted 14/02/12 04:13 AM Does it feel sluggish on hot/humid days, but decent on cool days? Link to comment Share on other sites More sharing options...
Zadz Member 63 Member For: 16y 4m 22d Gender: Male Location: WA Perth Posted 14/02/12 04:28 AM Share Posted 14/02/12 04:28 AM Yehit does, lol but that's a given with temp changes and forced induction cars.Other then the normal variances, sometimes even in crisp morning/night air it can feel drained. Saying that though, since iv played around with a few things its gotten better.Last to check on my list is cold side IC piping, from full 2 3/4inch to about half that cos compressed under headlight. Im assuming that cant be good with power figures.Was my own fault, did some hacking into it to add bov etc, cheats way out, now I returned back to orignal setup im lacking some length. Link to comment Share on other sites More sharing options...
Slash Donkey Dick Member 801 Member For: 14y 7m 22d Gender: Male Posted 14/02/12 06:21 AM Share Posted 14/02/12 06:21 AM You have the original Nizpro cooler, or the revised thicker one with 3" piping?Check your cat & O2 sensors Link to comment Share on other sites More sharing options...
Cheaty McCheats Totally not a Cop Donating Members 821 Member For: 13y 9m 16d Gender: Male Location: Melbourne Posted 14/02/12 07:01 AM Share Posted 14/02/12 07:01 AM Checked for codes? Link to comment Share on other sites More sharing options...
Zadz Member 63 Member For: 16y 4m 22d Gender: Male Location: WA Perth Posted 14/02/12 07:53 AM Share Posted 14/02/12 07:53 AM have the original it seams, not 3inch, seems 2 3/4 inch. Checked cat, while I had it off, I punched it......Havernt checked for codes as only got old xcal1. Link to comment Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,323 Member For: 19y 1m 18d Gender: Male Location: Perth Posted 14/02/12 08:46 AM Share Posted 14/02/12 08:46 AM Anybody out there with standard brakes keen for a set ot 330 X 28mm front rotors, C6 calipers and lines as removed from Toady's car? They need a set of pad and fitting and there good too go,A carton too myself or Toady would cover it, Would like them gooooorne before the weekend save me dragging them too the tip.I'm looking @ you tom...................... Link to comment Share on other sites More sharing options...
RIP_HSV HOON Member 1,636 Member For: 14y 7m 26d Gender: Male Location: W.A Posted 14/02/12 10:52 AM Share Posted 14/02/12 10:52 AM The Place could be called Repco 10 Speed for all I can, the important part is that its 40 odd Km's away from all the wierdo's down around Rockingham and Beeliar, and that's all that really matters. FIXED Link to comment Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,323 Member For: 19y 1m 18d Gender: Male Location: Perth Posted 14/02/12 11:00 AM Share Posted 14/02/12 11:00 AM *kelmscott may or may not have been a sly dig at a bloke that drives a blue ute Link to comment Share on other sites More sharing options...
RIP_HSV HOON Member 1,636 Member For: 14y 7m 26d Gender: Male Location: W.A Posted 14/02/12 11:02 AM Share Posted 14/02/12 11:02 AM *kelmscott is scary as hellYour not wrong mate lol Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now