Jump to content

WA Spotted & Chit Chat Thread


cunners

Recommended Posts

  • Moar Powar Babeh
  • Lifetime Members
  • Member For: 19y 1m 24d
  • Gender: Male
  • Location: Perth

Pardon the laconic knowledge but how bad is that Gruggles? Fkn cars eh

Rebuild time? If so can smash on a t51z or something :)

Air = compressable when squeezed, Water = Damn near solid. Water in engine in the space normally reserved for squashable air = at best bent rods, at worst rods exit stage left :ekk: :nukem:

Edit: nice one Steve, way to Pull off the :ninja: edit and explain what I explained two posts before mine and make me look like a Dik :) A lesser mod would edited your post to reflect your love for Justing Beiber and Ponies, buy ima take the higher moral ground.....

(I might just leave some bits loose under your car instead......muhahhaha)

Link to comment
Share on other sites

  • Manual mode ________________________ All day, erryday
  • Donating Members
  • Member For: 16y 11m 23d
  • Gender: Male
  • Location: Probably above atmospheric pressure

But at least the water can drain from the hole then!

Link to comment
Share on other sites

  • Manual mode ________________________ All day, erryday
  • Donating Members
  • Member For: 16y 11m 23d
  • Gender: Male
  • Location: Probably above atmospheric pressure

Whoah now it's all messed up :) Your reply wasn't there when I reloaded the page so nyah nyah!

Link to comment
Share on other sites

  • Dropping a turd
  • Gold Donating Members
  • Member For: 17y 20d
  • Gender: Male
  • Location: Perth

that's bad luck grug, hope its minimum damage. I'm with you Luke but dont worry about Steve poor bloke has to drive a car with stock wheels and low power, so lets make an exception for him.

Link to comment
Share on other sites

  • Sandtrap Motorsport
  • Donating Members
  • Member For: 15y 11m 22d
  • Gender: Male
  • Location: Perth

Hey Brendan (Grug) ... if you are going to get a new motor etc let me know if you are going to sell the internals of the old motor ... got somebody keen on the pistons if they are in good condition :)

Link to comment
Share on other sites

  • Donating Members
  • Member For: 15y 11m 11d
  • Gender: Male
  • Location: Pertthh W.A

After the problems I had in my previous F6 with the under batter intake I will never recommend one again. Spewing mate

Link to comment
Share on other sites

  • Manual mode ________________________ All day, erryday
  • Donating Members
  • Member For: 16y 11m 23d
  • Gender: Male
  • Location: Probably above atmospheric pressure

Might be time to make a big call on the car vs house thing man :( Unless you can find a cheapish way to get back to where you were, any idea what you're looking at already?

While I was down at XFT hearing about the aquatic adventures of the Grug mobile and lamenting my low power and stock rims (John's getting an even bigger blower put on, too many SC V8's around now!), I grabbed a couple pics of the new 19" Ford USA rims Simon has thrown on the F6:

2011-06-25093610.jpg

Rear fitment was pleasing to the eye... ten inch rears should do that though! 9 inch fronts as well.

2011-06-25093406crop.jpg

I suggested to Chippa he get them as they are a lazy 2 grand and look sharp but he's sensible and looking at 18's :P

Link to comment
Share on other sites

  • Get It To Wheelspin Uncontrolably Then Give It Another 5 Pounds
  • Cruise Control
  • Member For: 14y 26d
  • Gender: Male
  • Location: Work

Hey! :P

Car being towed to Simon's on Monday.. Hoping damage is minimal. Meanwhile, driving my mums diesel turbo van to work, wooo fun.

And these forums are getting slow again, lets get the next cruise organised.

..... so u gonna suggest we delay the cruze now Grug? hope u can put it back 2gether soon.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
  • Create New...
'