xr6t ego Member 1,112 Member For: 18y 3d Gender: Male Location: PERTH WA Posted 23/04/11 05:47 AM Share Posted 23/04/11 05:47 AM Goodluck Mike, you should claim a few scalps.. Was it the Alstar tail shaft loop from Chris Mills the one you purchased?Woo Whoo the cars back on the road. A big big thanks to Luke for all of the help, just need to clean of his grubby finger prints now. Thanks again. Will post up some more pics when cleaned up.Wheelgleam has done all of my polishing and more than happy to recommend them to people wanting something polished. Link to comment Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,323 Member For: 19y 3m 5d Gender: Male Location: Perth Posted 23/04/11 06:19 AM Share Posted 23/04/11 06:19 AM Glad your happy mate, looks the business now its all back together. ( Im sure the AWOL plenum nut will turn up one day.... :idontknow:)Oh and im sure those finger prints are yours...................... Link to comment Share on other sites More sharing options...
XF Falcon <put funny sh*t here> Member 3,365 Member For: 18y 1m 19d Gender: Male Location: Perth, NOR Posted 23/04/11 08:20 AM Share Posted 23/04/11 08:20 AM (edited) Brendan, it looks identical to the Alstar one on the Chris Mills website, but its boxed as a RPC brand one.I wasn't keen on drilling holes in the floor/chasis so I decided to modify the RPC one and use the gearbox cross member bolts.Here is how it is out of the boxRoughly where it sits on the car.Measured how long it should be and chopped the ends off them. I then had to grind down some of the sides so I could use the hole on the end to go through the cross member bolt properly. Once I was happy with how it fit on the cross member, I tacked it together, checked it all fitted good, then welded it all up properly, tidied them up a bit then gave it a coat of paint.I decided to leave the loop part unpainted so its a bit more visible at scrutineering.This is how it looks fitted. Its very solid and sits within 150mm of the front uni, so hopefully its good enough. Edited 23/04/11 08:23 AM by XF Falcon Link to comment Share on other sites More sharing options...
Tocchi Sandtrap Motorsport Donating Members 2,055 Member For: 16y 1m 3d Gender: Male Location: Perth Posted 23/04/11 09:32 AM Share Posted 23/04/11 09:32 AM RIP_HSV, the ute is looking good liking the fuel setup Link to comment Share on other sites More sharing options...
arronm Dropping a turd Gold Donating Members 9,520 Member For: 17y 2m 1d Gender: Male Location: Perth Posted 23/04/11 09:35 AM Share Posted 23/04/11 09:35 AM Gee Mike your member looks quite small entering thru that large hole. Link to comment Share on other sites More sharing options...
XF Falcon <put funny sh*t here> Member 3,365 Member For: 18y 1m 19d Gender: Male Location: Perth, NOR Posted 23/04/11 09:58 AM Share Posted 23/04/11 09:58 AM I can assure you the member is more than big enough for the job (has been confirmed from multiple sources) However in this case I'm working with an extremely big hole and by comparison it does look quite small I'm not sure how to make it smaller to tell you the truth. It can't lift any higher as it hits the floor of the car, and I can't chop make the loop halves any smaller as they won't touch the sides and bolt up properly any more. Link to comment Share on other sites More sharing options...
Grug Member 1,318 Member For: 16y 4m 29d Posted 23/04/11 10:30 AM Share Posted 23/04/11 10:30 AM What you did there, I see it. Link to comment Share on other sites More sharing options...
discostig Manual mode ________________________ All day, erryday Donating Members 13,798 Member For: 17y 1m 3d Gender: Male Location: Probably above atmospheric pressure Posted 23/04/11 11:27 AM Share Posted 23/04/11 11:27 AM Great work avoiding drilling holes in the car Mike. If I ever bother to get a TS loop put in I'd be the same. Link to comment Share on other sites More sharing options...
djkice Boost Addict Member 1,273 Member For: 16y 5m 6d Gender: Male Location: Perth, W.A. Posted 23/04/11 12:12 PM Share Posted 23/04/11 12:12 PM Does anyone have a 1.06 rear housing to suit a GT4094 they want to part with or swap with a .85?the 85 spools nicer...you looking to make more power? Link to comment Share on other sites More sharing options...
Cheaty McCheats Totally not a Cop Donating Members 821 Member For: 13y 11m 3d Gender: Male Location: Melbourne Posted 23/04/11 01:01 PM Share Posted 23/04/11 01:01 PM (edited) Here ya go! Bit of a pain that it was real low light and Pat didn't have his expensive lens with him.I'll try get him along on the next cruise with good glass so we can get some nice photos of everyones cars. Edited 23/04/11 01:02 PM by CyanideIllusions Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now